Home › TRANSMISSION ยท U660F AUTOMATIC TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT TRANSAXLE CASE OIL SEAL (INNER)


C196918E01
  1. Coat the lip of a new front transaxle case oil seal with MP grease.

  1. Using SST and a hammer, tap in the front transaxle case oil seal.

    SST
    09950-60010   (09951-00410)
    09950-70010   (09951-07200)

    Standard depth:
    21.5 to 22.5 mm (0.846 to 0.886 in.)



2. INSTALL DIFFERENTIAL SIDE GEAR


C196816E01
  1. Coat the 2 differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.



3. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT


C196815
  1. Coat the front No. 1 differential pinion shaft with ATF and install it to the differential case.



4. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH


C083562E01
  1. Hold the differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Place a dial indicator at a right angle to one of the side gear teeth.

  1. Hold the pinion gear in the differential case and measure the backlash of the side gear.

    Standard backlash:
    0 to 0.15 mm (0 to 0.00591 in.)

    Thrust Washer Thickness:
    Thickness
    Thickness
    1.50 mm (0.0591 in.)
    1.75 mm (0.0689 in.)
    1.55 mm (0.0610 in.)
    1.80 mm (0.0709 in.)
    1.60 mm (0.0630 in.)
    1.85 mm (0.0728 in.)
    1.65 mm (0.0650 in.)
    1.90 mm (0.0748 in.)
    1.70 mm (0.0669 in.)
    -

    If the backlash is not within the specified range, replace both side gear thrust washers with side gear thrust washers of a different thickness.



5. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


C196825
  1. Using a 3 mm pin punch and hammer, install the pinion shaft straight pin.

    NOTICE:
    Align the holes in the differential case and differential pinion shaft and install the pinion shaft straight pin.



    C196826
  1. Using a chisel and hammer, stake the differential case.

    NOTICE:
    Stake the differential case after inspecting the backlash.



6. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    C196827E02
  1. Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.

    SST
    09710-04081  
    09950-60010   (09951-00480)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during bearing inner race installation.



7. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


C196921E03
  1. Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.

    SST
    09710-04081  
    09950-60010   (09951-00480)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage during bearing inner race installation.



8. INSTALL FRONT DIFFERENTIAL RING GEAR


    D025215E10
  1. Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

    NOTICE:
    Do not heat the ring gear to higher than 110°C (230°F).

  1. Clean the contact surface of the front differential case.



    C196807E02
  1. Align the matchmarks, and quickly install the front differential ring gear to the differential case.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    Do not install the bolts while the ring gear is hot.



    C138532
  1. Install and tighten the 12 bolts.

    Torque:
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }

    NOTICE:
    Tighten the bolts in diametrically opposite pairs.