Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION ANTENNA

NAVIGATION ANTENNA > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


B129872
  1. Using a screwdriver, detach the 4 clips and 6 claws, and then remove the instrument cluster finish panel.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE COMBINATION METER ASSEMBLY


B136780
  1. Remove the 2 screws.

  1. Pull the combination meter in the direction indicated by the arrow in the illustration to detach the 2 clips.

  1. Disconnect the connector and remove the combination meter.



4. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208365
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER


    B208366
  1. Using a moulding remover, detach the 3 clips and 2 claws, and then remove the cluster finish panel.

  1. Disconnect the connector.



6. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET
  1. for HDD:

    1. Remove the navigation receiver assembly with bracket (Click here).

  1. for DVD:

    1. Remove the navigation receiver assembly with bracket (Click here).



7. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY CENTER


    B129890
  1. Using a moulding remover, detach the 5 clips and remove the instrument panel register.



8. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B129889E04
  1. Open the glove compartment door.

  1. Detach the claw from the glove compartment door stopper.

  1. While pushing in the sides of the glove compartment door in the direction indicated by the arrows in the illustration, open the door to release it from the 2 stoppers.



    B129888
  1. Open the door as much as possible.

  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.



9. REMOVE FRONT PILLAR GARNISH LH


    B129698
  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, detach the 2 clips.

    2. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.



    B203236E01
  1. w/ Curtain Shield Airbag:

    1. Detach the 2 clips.

    2. Cut off the 2 clips.

    3. Detach the 3 claws and remove the garnish.

    4. Remove the 2 clips from the vehicle body.

      NOTICE:
      As the clips are cut, be sure to install new clips when installing the garnish.



    B114316
  1. Using a clip remover, remove the 4 wiring harness clamps.



    B065292E06
  1. w/ Curtain Shield Airbag:

    1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



10. REMOVE FRONT PILLAR GARNISH RH


    B131251
  1. w/o Curtain Shield Airbag:

    1. Using a clip remover, detach the 2 clips.

    2. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.



    B203237E01
  1. w/ Curtain Shield Airbag:

    1. Detach the 2 clips.

    2. Cut off the 2 clips.

    3. Detach the 3 claws and remove the garnish.

    4. Remove the 2 clips from the vehicle body.

      NOTICE:
      As the clips are cut, be sure to install new clips when installing the garnish.



    B135443
  1. Using a clip remover, remove the 4 antenna cord clamps.



    B131254E01
  1. w/ Curtain Shield Airbag:

    1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



11. REMOVE UPPER INSTRUMENT PANEL


    B129886
  1. Remove the 2 bolts from the passenger airbag.

  1. Disconnect the passenger airbag connector.

  1. Remove the 2 bolts and 2 screws.

  1. Disconnect the connector and detach the clamp.



  1. Detach the 6 clips and 5 claws and remove the instrument panel.


    B208364



12. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT


    B208591
  1. Remove the 3 screws and duct.



13. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT


    B208592
  1. Remove the 3 screws and duct.



14. REMOVE NO. 1 HEATER TO REGISTER DUCT


    B208593
  1. Remove the screw and duct.



15. REMOVE NO. 2 HEATER TO REGISTER DUCT


    B208594
  1. Remove the screw and duct.



16. REMOVE NO. 3 HEATER TO REGISTER DUCT


    B208595
  1. Remove the 2 screws and duct.



17. REMOVE NAVIGATION ANTENNA ASSEMBLY


    E125791
  1. Remove the 2 screws and navigation antenna.