Home › BODY › EXTERIOR › FRONT BUMPER (w/ Under Guard)

FRONT BUMPER (w/ Under Guard) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT BUMPER SIDE RETAINER LH


B209172
  1. Install the retainer with the clip.

  1. Install the bolt.



2. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure described for the LH side.



3. INSTALL FRONT BUMPER REINFORCEMENT


  1. for Manual Transaxle:

    1. Install the reinforcement with the 8 bolts.

      Torque:
      70 N*m{ 714 kgf*cm , 52 ft.*lbf }



    2. Attach the 3 clamps to install the wire harness.


      B209928E01



    B225785E01
  1. for Automatic Transaxle:

    1. Install the reinforcement with the 10 bolts.

      Torque:
      for Bolt A:
      70 N*m{ 714 kgf*cm , 52 ft.*lbf }
      for Bolt B:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    2. Attach the 3 clamps to install the wire harness.



4. INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY


B211609
  1. Install the reinforcement with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



5. INSTALL LOW PITCHED HORN ASSEMBLY


E173377
  1. Install the horn with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the horn connector.



6. INSTALL HIGH PITCHED HORN ASSEMBLY


E173376
  1. Install the horn with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the horn connector.



7. INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY


  1. Install the stay with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    B209927E01



8. INSTALL FRONT BUMPER LOWER ABSORBER (w/ Front Bumper Lower Absorber)


B208312
  1. Install the lower absorber.



9. INSTALL FRONT BUMPER ENERGY ABSORBER (w/ Front Bumper Lower Absorber)


B208311
  1. Install the 2 energy absorbers.



10. INSTALL FRONT NO. 2 BUMPER ENERGY ABSORBER


  1. Install the energy absorber.


    B209931E01



11. INSTALL FRONT BUMPER COVER


    B208307
  1. Connect the 2 fog light connectors.

  1. Attach the 4 claws to install the bumper cover.

    HINT:
    The illustration only shows the LH side of the vehicle. The remaining claws are on the RH side.



    B209203
  1. Install the 8 screws and 4 clips.



    B209205
  1. Install the retainer.

    HINT:
    Use the same procedure for RH and LH sides.

  1. Position the groove on the pin hold clip vertically and insert the clip to install it.

    NOTICE:
    Make sure that the groove on the pin hold clip is positioned vertically.

    HINT:
    Use the same procedure for RH and LH sides.



12. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH


B208332
  1. Install the splash shield with the nut, bolt and screw.



13. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

HINT:
Use the same procedure described for the LH side.



14. INSTALL RADIATOR GRILLE PROTECTOR


B209174
  1. Install the 2 radiator grille protectors.



15. INSTALL CENTER HOOD CUSHION


B209173
  1. Install the hood cushion.



16. INSTALL RADIATOR SUPPORT OPENING COVER


B209240
  1. Install the radiator support opening cover with the 9 clips.