Home › BODY › EXTERIOR › FRONT BUMPER (w/ Under Guard)

FRONT BUMPER (w/ Under Guard) > DISASSEMBLY

for Preparation Click here



1. REMOVE HOOD TO RADIATOR GRILLE SEAL


B208347E01
  1. Remove the 4 clips.

  1. Detach the 9 clips and remove the hood to radiator grille seal.



2. REMOVE RADIATOR GRILLE SUB-ASSEMBLY


B208459
  1. for Type A:

    1. Remove the 3 bolts.

    2. Detach the 24 claws and 4 guides, and remove the radiator grille.



    B211608
  1. for Type B:

    1. Remove the 3 bolts.

    2. Detach the 20 claws and 4 guides, and remove the radiator grille.



3. REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


B208335
  1. Detach the 3 claws and remove the emblem.



4. REMOVE FRONT NO. 2 BUMPER SIDE RETAINER LH


B208339
  1. Remove the 2 screws and retainer.



5. REMOVE FRONT NO. 2 BUMPER SIDE RETAINER RH

HINT:
Use the procedure described for the LH side.



6. REMOVE FRONT BUMPER ARM EXTENSION LH


B208464
  1. Remove the 3 screws.

  1. Using a clip remover, remove the clip.

  1. Detach the 3 claws and remove the arm extension.



7. REMOVE FRONT BUMPER ARM EXTENSION RH

HINT:
Use the procedure described for the LH side.



8. REMOVE FRONT NO. 1 BUMPER EXTENSION RETAINER


B208472
  1. Remove the 2 retainers.

    HINT:
    Use the same procedure for the RH and LH sides.



9. REMOVE LOWER NO. 2 RADIATOR GRILLE


B208346
  1. Remove the 2 screws and 4 bolts.

  1. Detach the 6 claws and remove the lower No. 2 radiator grille.



10. REMOVE FRONT BUMPER BAR


B208341E01
  1. Using a heat light, heat the lower No. 2 radiator grille and bumper bar.

    Standard:
    Item
    Temperature
    Lower No. 2 radiator grille
    20 to 30°C (68 to 86°F)
    Bumper bar
    20 to 30°C (68 to 86°F)

    NOTICE:
    Do not heat the lower No. 2 radiator grille and bumper bar excessively.

  1. Insert a piano wire between the lower No. 2 radiator grille and bumper bar.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

  1. Pull the piano wire and scrape off the double-sided tape that holds the bumper bar to the lower No. 2 radiator grille.

    NOTICE:
    Be careful not to damage the lower No. 2 radiator grille.



11. REMOVE CENTER RADIATOR GRILLE MOULDING LH


B208343
  1. Detach the 3 claws and remove the center radiator grille moulding.



12. REMOVE CENTER RADIATOR GRILLE MOULDING RH

HINT:
Use the same procedure described for the LH side.



13. REMOVE LOWER RADIATOR GRILLE MOULDING


B208345
  1. Detach the 9 claws and remove the lower radiator grille moulding.



14. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET


B219393
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the mounting bracket.



15. REMOVE FRONT BUMPER HOLE COVER LH


B208468
  1. Detach the 4 claws and remove the hole cover.



16. REMOVE FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure described for the LH side.



17. REMOVE FOG LIGHT ASSEMBLY LH


B208470
  1. Remove the screw.

  1. Detach the 2 guides and remove the fog light.



18. REMOVE FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



19. REMOVE HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)


  1. w/o Under Guard:



      E179678
    1. Disconnect the headlight washer hose from the headlight washer actuator.

    2. Detach the 5 clamps and remove the hose from the front bumper.



  1. w/ Under Guard:



      E179679
    1. Disconnect the headlight washer hose from the headlight washer actuator.

    2. Detach the 5 clamps and remove the hose from the front bumper.



20. REMOVE HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E181256
  1. Extend the headlight cleaner washer nozzle.



    E179681
  1. Detach the 2 claws and remove the headlight cleaner washer nozzle.



21. REMOVE HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.



22. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E179680
  1. Remove the 2 screws.



    E179677
  1. Detach the 2 claws and remove the headlight washer actuator sub-assembly.



23. REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.