Home › BODY › EXTERIOR › FRONT BUMPER (w/ Under Guard)

FRONT BUMPER (w/ Under Guard) > REASSEMBLY

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E179677
  1. Attach the 2 claws to install the headlight washer actuator sub-assembly.



    E179680
  1. Install the headlight washer actuator with the 2 screws.



2. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.



3. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)


    E179681
  1. Attach the 2 claws to install the headlight washer nozzle.



4. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.



5. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)


  1. w/o Under Guard:



      E179678
    1. Attach the 5 clamps to install the hose to the front bumper.

    2. Connect the clamp to the headlight washer hose.



  1. w/ Under Guard:



      E179679
    1. Attach the 5 clamps to install the hose to the front bumper.

    2. Connect the clamp to the headlight washer hose.



6. INSTALL FOG LIGHT ASSEMBLY LH


B208470
  1. Attach the 2 guides to install the fog light.

  1. Install the screw.



7. INSTALL FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



8. INSTALL FRONT BUMPER HOLE COVER LH


B208468
  1. Attach the 4 claws to install the bumper hole cover.



9. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure described for the LH side.



10. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET


B219393
  1. Attach the 2 claws to install the front bumper extension mounting bracket.

  1. Install the 2 screws.



11. INSTALL LOWER RADIATOR GRILLE MOULDING


B208345
  1. Attach the 9 claws to install the lower radiator grille moulding.



12. INSTALL CENTER RADIATOR GRILLE MOULDING LH


B208343
  1. Attach the 3 claws to install the center radiator grille moulding.



13. INSTALL CENTER RADIATOR GRILLE MOULDING RH

HINT:
Use the same procedure described for the LH side.



14. INSTALL FRONT BUMPER BAR
  1. Clean the lower No. 2 radiator grille surface.

    1. Using a heat light, heat the lower No. 2 radiator grille surface.

      Standard:
      Item
      Temperature
      Lower No. 2 radiator grille
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the lower No. 2 radiator grille excessively.

    2. Remove the double-sided tape from the lower No. 2 radiator grille.

    3. Wipe off any tape adhesive residue with cleaner.

  1. If reusing the bumper bar, clean the bumper bar.

    1. Remove the double-sided tape from the bumper bar.

    2. Wipe off any tape adhesive residue with cleaner.

    3. Apply new double-sided tape to the bumper bar.



    B209248E01
  1. Install the bumper bar.

    1. Using a heat light, heat the lower No. 2 radiator grille and bumper bar.

      Standard:
      Item
      Specified Condition
      Lower No. 2 radiator grille
      20 to 30°C (68 to 86°F)
      Bumper bar
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the lower No. 2 radiator grille and bumper bar excessively.

    2. Remove the peeling paper from the face of the bumper bar.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Install the bumper bar.

      HINT:
      Press the bumper bar firmly to install it.



15. INSTALL LOWER NO. 2 RADIATOR GRILLE


B208346
  1. Attach the 6 claws to install the lower No. 2 radiator grille.

  1. Install the 2 screws and 4 bolts.



16. INSTALL FRONT NO. 1 BUMPER EXTENSION RETAINER


B208472
  1. Install the 2 retainers.

    HINT:
    Use the same procedure for the RH and LH sides.



17. INSTALL FRONT BUMPER ARM EXTENSION LH


B208464
  1. Attach the 3 claws to install the arm extension.

  1. Install the 3 screws and clip.



18. INSTALL FRONT BUMPER ARM EXTENSION RH

HINT:
Use the same procedure described for the LH side.



19. INSTALL FRONT NO. 2 BUMPER SIDE RETAINER LH


B208339
  1. Install the retainer with the 2 screws.



20. INSTALL FRONT NO. 2 BUMPER SIDE RETAINER RH

HINT:
Use the same procedure described for the LH side.



21. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


B208335
  1. Attach the 3 claws to install the emblem.



22. INSTALL RADIATOR GRILLE SUB-ASSEMBLY


B208459
  1. for Type A:

    1. Attach the 24 claws and 4 guides to install the radiator grille.

    2. Install the 3 bolts.



    B211608
  1. for Type B:

    1. Attach the 20 claws and 4 guides to install the radiator grille.

    2. Install the 3 bolts.



23. INSTALL HOOD TO RADIATOR GRILLE SEAL
  1. Clean the bumper cover surface.

    1. Using a heat light, heat the bumper cover surface.

      Standard:
      Item
      Temperature
      Bumper cover
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the bumper cover excessively.

    2. Remove the double-sided tape from the bumper cover.

    3. Wipe off any tape adhesive residue with cleaner.



    B208347E01
  1. Install a new hood to radiator grille seal.

    1. Using a heat light, heat the bumper cover and hood to radiator grille seal.

      Standard:
      Item
      Temperature
      Bumper cover
      20 to 30°C (68 to 86°F)
      Hood to radiator grille seal
      20 to 30°C (68 to 86°F)

      NOTICE:
      Do not heat the bumper cover and hood to radiator grille seal excessively.

    2. Attach the 9 clips to install the hood to radiator grille seal.

    3. Install the 4 clips.

    4. Remove the peeling paper from the face of the hood to radiator grille seal.

    5. Attach the double-sided tape on the hood to radiator grille seal to the bumper cover.

      HINT:
      Press the hood to radiator grille seal firmly to install it.