Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

CRUISE CONTROL SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



CRUISE CONTROL SYSTEM
The cruise control system controls the vehicle speed by using the ECM to change the fuel injection quantity. The ECM controls the following functions: ON-OFF, - (COAST)/SET, + (ACCEL)/RES, CANCEL, vehicle speed operation, motor output control, and shift down control.
  1. The ECM compares the vehicle speed from the speed sensor with the stored vehicle speed set through the cruise control main switch. When the actual vehicle speed exceeds the stored vehicle speed, the ECM decreases the fuel injection quantity. When the actual vehicle speed is less than the stored vehicle speed, the ECM increases the fuel injection quantity.
  2. The ECM receives signals such as ON-OFF, - (COAST)/SET, + (ACCEL)/RES, and CANCEL from the cruise control main switch and executes the command.
  3. The ECM illuminates the combination meter's CRUISE main indicator light when it receives the cruise control main switch ON signal.
  4. The ECM cancels the cruise control system when the brake pedal is depressed and the ECM receives the stop light switch signal.
  5. The ECM cancels the cruise control system when 1) the shift lever is moved from D to N or M, or the shift range is changed to M3, M2 or M1 using the shift paddle switch, and 2) the ECM receives the park/neutral position switch signal (when the shift lever is moved to N), transmission control switch signal (when the shift lever is moved to M) or transmission shift switch signal (when the shift range is changed to M3, M2 or M1) (for Automatic Transaxle).
  6. The ECM cancels the cruise control system when the clutch pedal is depressed and the ECM receives the clutch switch signal (for Manual Transaxle).

LIMIT CONTROL
  1. Low speed limit
    The lowest possible limit of the speed setting range is set at approximately 40 km/h (25 mph). The cruise control system cannot be set when the driving vehicle speed is below the low speed limit. Cruise control operation will be automatically canceled when the vehicle speed decreases below the low speed limit 40 km/h (25 mph) while the cruise control is in operation.

  2. High speed limit
    The highest possible limit of the speed setting range is set at approximately 200 km/h (125 mph). The cruise control system cannot be set when the driving vehicle speed is over the high speed limit. Also, + (ACCEL)/RES cannot be used to increase speed beyond the high speed limit.


OPERATION OF CRUISE CONTROL
The cruise control main switch operates 7 functions: SET, COAST, TAP-DOWN, RESUME, ACCELERATION (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN and COAST functions, and the RESUME, TAP-UP and ACCEL functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only when pressed in each arrow direction and turns off when released.
  1. SET CONTROL
    Vehicle speed is stored and constant speed control is maintained when setting the cruise control main switch to - (COAST)/SET while driving with the cruise control main switch ON (the CRUISE main indicator light is illuminated), and the vehicle speed is within the set speed range (between the low and high speed limits).

  2. COAST CONTROL
    When the - (COAST)/SET on the cruise control main switch is pressed and held while the cruise control system is operating, the ECM changes the required fuel injection quantity to 0 and decelerates the vehicle. When the cruise control main switch is released from - (COAST)/SET, the vehicle speed is stored and constant speed control is maintained.

    HINT:
    w/ VSC:
    The brake is also used to decelerate the vehicle.

  3. TAP-DOWN CONTROL
    When tapping down the cruise control main switch to - (COAST)/SET (for approximately 0.6 seconds) while the cruise control system is operating, the stored vehicle speed decreases each time by approximately 1.6 km/h (1.0 mph). When the cruise control main switch is released from - (COAST)/SET and the difference between the driving and the stored vehicle speed is less than 5 km/h (3 mph), the vehicle speed is stored and constant speed is maintained.

  4. ACCEL CONTROL
    While the cruise control system is activated, if the cruise control main switch is set to + (ACCEL)/RES, the EDU increases the fuel injection quantity. When the cruise control main switch is released from + (ACCEL)/RES, the vehicle speed is stored and constant speed is maintained.

  5. TAP-UP CONTROL
    When tapping up the cruise control main switch to + (ACCEL)/RES (for approximately 0.6 seconds) while the cruise control system is operating, the stored vehicle speed increases each time by approximately 1.6 km/h (1.0 mph). However, when the difference between the driving and the stored vehicle speed is more than 5 km/h (3 mph), the stored vehicle speed will not be changed.

  6. RESUME CONTROL
    If the cruise control operation was canceled with the stop light switch or the CANCEL switch and if driving speed is within the set speed range, setting the cruise control main switch to + (ACCEL)/RES restores the vehicle speed memorized at the time of cancellation and constant speed is maintained.

  7. MANUAL CANCEL CONTROL
    Performing any of the following cancels the cruise control system.

    1. Depressing the brake pedal
    2. Pulling the cruise control main switch to CANCEL
    3. The shift lever is moved from D to N or M (for Automatic Transaxle)
    4. The shift range is changed to M3, M2 or M1 when the shift lever is in D (for Automatic Transaxle)
    5. Depressing the clutch pedal (for Manual Transaxle)
    6. Pushing the cruise control main switch OFF (the stored vehicle speed in the ECM is not maintained)


AUTO CANCEL (FAIL-SAFE)
  1. This system has an automatic cancellation function (fail-safe) (Click here).