Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for HDD)

NAVIGATION SYSTEM (for HDD) > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the navigation receiver and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM


E182158E03


INSPECTION PROCEDURE

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.
    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except navigation receiver.
    B
    No illumination comes on (navigation receiver, hazard switch, glove box, etc.).
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY)


    E121218E20
  1. Disconnect the E10 spiral cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E10-12 (IL+2) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly (Click here).



  1. Connect the positive (+) lead of the battery to terminal 5 (IL+2) and the negative (-) lead to terminal 8 (EAU) of the steering pad switch connector.


    E185289E01

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY


    B220324E02
  1. Remove the spiral cable sub-assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    8 (EAU) - 4 (EAU)
    Spiral cable is turned 2.5 rotations counterclockwise
    Below 1 Ω
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise
    5 (IL+2) - 12 (IL+2)
    Spiral cable is turned 2.5 rotations counterclockwise
    Spiral cable is centered
    Spiral cable is turned 2.5 rotations clockwise

    CAUTION:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - SPIRAL CABLE)


    E179014E12
  1. Disconnect the E106 navigation receiver connector.



    E179015E06
  1. Disconnect the E10 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E106-6 (SWG) - E10-4 (EAU)
    Always
    Below 1 Ω
    E106-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY)


    E141019E54
  1. Disconnect the E52 navigation receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E52-10 (ILL+) - Body ground
    Light control switch TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)