Home › ENGINE ยท 2AD-FTV › LUBRICATION › ENGINE OIL COOLER

ENGINE OIL COOLER > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



1. REMOVE NO. 1 ENGINE COVER


    A203808
  1. Detach the 4 clips and remove the engine cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.



2. REMOVE RADIATOR SUPPORT OPENING COVER


B209240
  1. Remove the 9 clips and radiator support opening cover.



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



4. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 6 bolts, 10 clips and engine under cover.



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the clip and open the oil pan drain service cover.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Close the oil pan drain service cover and install the clip



6. DRAIN ENGINE COOLANT
  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator reservoir cap.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



  1. Loosen the cylinder block drain cock plug.

    HINT:
    The plug is on the backside of the generator on the EGR cooler side.



    A208259E01


    Text in Illustration 
    *1
    Radiator Reservoir Cap
    *2
    Radiator Reservoir
    *3
    Cylinder Block Drain Cock
    *4
    Radiator Drain Cock Plug



7. REMOVE NO. 3 AIR HOSE


    A208799
  1. Loosen the 2 hose clamps.

  1. Remove the No. 3 air hose from the No. 2 air tube and throttle body.



8. REMOVE DIESEL THROTTLE BODY ASSEMBLY


    A203104
  1. Disconnect the No. 7 water by-pass hose from the throttle body.

  1. Disconnect the No. 6 water by-pass hose from the throttle body.

  1. Disconnect the throttle position sensor and throttle motor connector.



    A203105
  1. Remove the 2 nuts, 2 bolts, diesel throttle body and gasket.



9. DISCONNECT ENGINE WIRE


A207973
  1. Disconnect the vacuum regulating valve connector.

  1. Disconnect the vacuum switching valve connector.

  1. Disconnect the 4 injector connectors.

  1. Remove the grommet and nut, and disconnect the glow plug wire harness.

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the emission control valve wire connector.

  1. Disconnect the pressure discharge valve connector.

  1. Remove the bolt and disconnect the engine wire from the bracket.

  1. Remove the bolt and 5 nuts, and disconnect the engine wire.



10. REMOVE EGR VALVE BRACKET


    A206310
  1. Disconnect the 2 connectors and detach the wire harness clamp.



    A206475
  1. Remove the 3 bolts and EGR valve bracket.



11. REMOVE NO. 7 WATER BY-PASS HOSE


A197539


12. DISCONNECT NO. 8 WATER BY-PASS HOSE


A201867


13. REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY


    A197538
  1. Disconnect the electric EGR control valve connector.



    A197541E01
  1. Remove the 3 bolts, 2 nuts, No. 2 EGR pipe and 2 gaskets.
    Text in Illustration 
    *1
    Nut



14. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY


    A197543
  1. Remove the electric EGR control valve and gasket.



15. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
After removing the fuel inlet pipe, cover the common rail and supply pump with electrical tape to prevent dirt from entering them.



    A203053
  1. Remove the nut and 2 clamps.

  1. Using a 14 mm union nut wrench, remove the fuel inlet pipe.



16. REMOVE INJECTION PIPE SUB-ASSEMBLY

NOTICE:
After removing the injection pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.



    A203038
  1. Remove the 2 bolts and 4 injection pipe clamps.

  1. Using a 14 mm union nut wrench, loosen the 4 nuts at the common rail end of the injection pipes.

  1. Using a 14 mm union nut wrench, loosen the 4 nuts at the injector end of the injection pipes.

  1. Remove the 4 injection pipes.



17. REMOVE COMMON RAIL ASSEMBLY


    A201874
  1. Remove the 2 bolts and common rail.



18. REMOVE INTAKE MANIFOLD INSULATOR


    A197550
  1. Remove the intake manifold insulator from the intake manifold.



19. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.



    A197547
  1. Remove the 2 bolts and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



20. REMOVE DIESEL TURBO PRESSURE SENSOR


    A197551
  1. Disconnect the vacuum hose.

  1. Remove the bolt and sensor.



21. REMOVE NO. 1 GAS FILTER


    A206311
  1. Disconnect the vacuum hose.

  1. Remove the No. 1 gas filter from the gas filter bracket.



22. REMOVE GAS FILTER BRACKET


    A206312
  1. Remove the 2 bolts and gas filter bracket.



23. REMOVE ENGINE COVER BRACKET


    A197556
  1. Remove the bolt and engine cover bracket.



24. REMOVE NO. 2 INTAKE MANIFOLD


    A197557
  1. Remove the bolt, 2 nuts, No. 2 intake manifold and gasket.



25. DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE


    A201877
  1. Disconnect the No. 2 vacuum transmitting hose from the intake manifold.



26. REMOVE INTAKE MANIFOLD


    A197558E01
  1. Remove the 7 bolts, 2 nuts, intake manifold and gasket.
    Text in Illustration 
    *1
    Nut



27. REMOVE NO. 1 WATER BY-PASS HOSE


A197563


28. REMOVE OIL COOLER ASSEMBLY


    A197565
  1. Remove the 5 bolts and oil cooler.

  1. Remove the 3 O-rings from the oil cooler bracket.