Home › ENGINE ยท 2AD-FTV › LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.
  3. In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the clip and open the oil pan drain service cover.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Close the oil pan drain service cover and install the clip



2. REMOVE OIL FILTER ELEMENT


    A094910E07
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.
    Text in Illustration 
    *1
    Oil Filter Drain Pipe
    *2
    Hose

  1. Remove the clip and open the oil filter element service cover.



    A210247
  1. Remove the oil filter drain plug.

  1. Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.



    A201803E01
  1. Install the oil filter drain pipe to the oil filter cap and drain the engine oil.
    Text in Illustration 
    *1
    Oil Filter Cap
    *2
    O-Ring
    *3
    Oil Filter Drain Pipe

  1. Remove the oil filter drain pipe.

  1. Apply a light coat of engine oil to a new O-ring and install it to the oil filter drain plug.



    A210247
  1. Install the oil filter drain plug to the oil filter cap.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    A210248E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  



    A201807E01
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand without using any tools to prevent damage to the cap O-ring groove.



3. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, its threads and its O-ring groove.



    A201807E01
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
    Text in Illustration 
    *1
    New Oil Filter Element
    *2
    New O-Ring

  1. Set a new oil filter element in the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

  1. Check and clean the oil filter installation surface.



    A210249E01
  1. Using SST, tighten the oil filter cap.

    SST
    09228-06501  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Close the oil filter element service cover and install the clip.



4. ADD ENGINE OIL
  1. Add new engine oil.

    Standard Oil Grade:

    Item
    Oil Grade
    Oil Viscosity (SAE)
    for CCo:
    Diesel fuel that contains between 50 ppm and 500 ppm of sulfur
    ACEA B1, API CF-4 or CF
    (You may also use API CE or CD)
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50
    for CCo:
    Diesel fuel that contains 50 ppm or less of sulfur
    ACEA C2, B1, API CF-4 or CF
    (You may also use API CE or CD)
    - 0W-30
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50
    for DPF
    ACEA C2
    - 0W-30
    - 5W-30


    Standard Capacity:

    Item
    Specified Condition
    Drain and refill without oil filter change
    5.5 liters (5.8 US qts, 4.8 Imp. qts)
    Drain and refill with oil filter change
    5.9 liters (6.2 US qts, 5.2 Imp. qts)
    Dry fill
    6.7 liters (7.1 US qts, 5.9 Imp. qts)



5. INSPECT FOR OIL LEAK
  1. Warm up the engine and check for an engine oil leak.



6. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.