Home › ENGINE ยท 2AD-FTV › ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
w/ Navigation System (for HDD):
After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE ENGINE ASSEMBLY
  1. Remove the engine assembly (Click here).



3. DISCONNECT ENGINE WIRE
  1. Disconnect the connectors and clamps securing the engine wire to the engine, remove the bracket bolts and disconnect the engine wire from the engine.



4. REMOVE GENERATOR ASSEMBLY


    A196712
  1. Remove the 3 bolts and generator.



5. REMOVE VACUUM PUMP ASSEMBLY


    A201743
  1. Disconnect the vacuum hose.

  1. Remove the 3 bolts and vacuum pump.

  1. Remove the 2 O-rings from the vacuum pump.



6. REMOVE IDLER PULLEY COVER PLATE


    A201745E01
  1. Using a screwdriver, remove the idler pulley cover plate.
    Text in Illustration 
    *1
    Tape

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A201746
  1. Remove the bolt and No. 1 idler pulley.



8. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A201747E01
  1. Remove the bolt, No. 2 idler pulley cover plate and No. 2 idler pulley.
    Text in Illustration 
    *1
    No. 2 Idler Pulley Cover Plate
    *2
    No. 2 Idler Pulley



9. REMOVE NO. 4 WATER BY-PASS PIPE


    A201735
  1. Remove the bolt and No. 4 water by-pass pipe from the water inlet housing.

  1. Remove the O-ring from the No. 4 water by-pass pipe.



10. REMOVE ENGINE MOUNTING BRACKET


    A201748
  1. Remove the 4 bolts, 2 nuts and engine mounting bracket.



11. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A201749
  1. Remove the 3 bolts and V-ribbed belt tensioner.

    NOTICE:
    As the heads of the bolts are not as thick as those of typical bolts, be careful not to damage them during removal.



12. REMOVE DIESEL THROTTLE BODY ASSEMBLY


    A201844E01
  1. Disconnect the No. 6 and No. 7 water by-pass hoses.
    Text in Illustration 
    *1
    No. 6 Water By-pass Hose
    *2
    No. 7 Water By-pass Hose



    A203105
  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.



13. REMOVE NO. 7 WATER BY-PASS HOSE


A197539


14. DISCONNECT NO. 8 WATER BY-PASS HOSE


A201867


15. REMOVE EGR VALVE BRACKET


    A212572
  1. Remove the 3 bolts and EGR valve bracket.



16. REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY


    A197538
  1. Disconnect the electric EGR control valve connector.



    A197541E01
  1. Remove the 3 bolts, 2 nuts, No. 2 EGR pipe and 2 gaskets.
    Text in Illustration 
    *1
    Nut



17. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY


    A197543
  1. Remove the electric EGR control valve and gasket.



18. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.



    A197547
  1. Remove the 2 bolts and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



19. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:
After removing the fuel inlet pipe, cover the common rail and supply pump with electrical tape to prevent dirt from entering them.



    A203053
  1. Remove the nut and 2 clamps.

  1. Using a 14 mm union nut wrench, remove the fuel inlet pipe.



20. REMOVE INJECTION PIPE SUB-ASSEMBLY

NOTICE:
After removing the fuel inlet pipe, cover the common rail and supply pump with electrical tape to prevent dirt from entering them.



    A203053
  1. Remove the nut and 2 clamps.

  1. Using a 14 mm union nut wrench, remove the fuel inlet pipe.



21. REMOVE NO. 4 FUEL HOSE


A197571


22. REMOVE COMMON RAIL ASSEMBLY


    A201874
  1. Remove the 2 bolts and common rail.



23. REMOVE INTAKE MANIFOLD INSULATOR


    A197550
  1. Remove the intake manifold insulator from the intake manifold.



24. REMOVE DIESEL TURBO PRESSURE SENSOR


    A197551
  1. Disconnect the vacuum hose.

  1. Remove the bolt and sensor.



25. REMOVE NO. 1 GAS FILTER


    A206311
  1. Disconnect the vacuum hose.

  1. Remove the No. 1 gas filter from the gas filter bracket.



26. REMOVE GAS FILTER BRACKET


    A206312
  1. Remove the 2 bolts and gas filter bracket.



27. REMOVE ENGINE COVER BRACKET


    A197556
  1. Remove the bolt and engine cover bracket.



28. REMOVE NO. 2 INTAKE MANIFOLD


    A197557
  1. Remove the bolt, 2 nuts, No. 2 intake manifold and gasket.



29. REMOVE INTAKE MANIFOLD


    A197558E01
  1. Remove the 7 bolts, 2 nuts, intake manifold and gasket.
    Text in Illustration 
    *1
    Nut



30. REMOVE NO. 1 WATER BY-PASS HOSE


A197563


31. REMOVE OIL COOLER ASSEMBLY


    A197565
  1. Remove the 5 bolts and oil cooler.

  1. Remove the 3 O-rings from the oil cooler bracket.



32. REMOVE NO. 6 WATER BY-PASS HOSE


    A201724
  1. Remove the No. 6 water by-pass hose.



33. REMOVE NO. 8 WATER BY-PASS HOSE


A201867


34. REMOVE NO. 3 WATER BY-PASS PIPE


    A201726
  1. Remove the 2 bolts and No. 3 water by-pass pipe.

  1. Remove the O-ring from the No. 3 water by-pass pipe.



35. REMOVE NO. 1 TURBO OIL PIPE


    A201727
  1. Remove the 2 union bolts, 2 gaskets and No. 1 turbo oil pipe.



36. REMOVE NO. 1 OIL COOLER BRACKET


    A201729E01
  1. Remove the 6 bolts, nut and No. 1 oil cooler bracket.
    Text in Illustration 
    *1
    Nut

  1. Remove the 3 O-rings from the No. 1 oil cooler bracket.



37. REMOVE NO. 1 CYLINDER BLOCK INSULATOR


    A201731
  1. Remove the No. 1 cylinder block insulator from the cylinder block.



38. REMOVE NO. 2 WATER BY-PASS PIPE


    A201732
  1. Remove the 2 bolts and No. 2 water by-pass pipe from the water inlet housing.



39. REMOVE NO. 4 WATER BY-PASS HOSE


    A201735
  1. Remove the bolt and No. 4 water by-pass pipe from the water inlet housing.

  1. Remove the O-ring from the No. 4 water by-pass pipe.



40. REMOVE WATER INLET HOUSING


    A142993
  1. Remove the 3 nuts and water inlet housing.

  1. Remove the gasket from the water inlet housing.



41. REMOVE NO. 2 FUEL PIPE (for CCo)


    A203051E02
  1. Remove the check valve and gasket.
    Text in Illustration 
    *1
    Check Valve

  1. Remove the union bolt, gasket and fuel pipe.



42. REMOVE FUEL HOSE PROTECTOR (for DPF)


    A206325
  1. Disconnect the connector.



    A197570
  1. Remove the bolt and fuel hose protector.



43. REMOVE FUEL TUBE SUB-ASSEMBLY (for DPF)


    A203047
  1. Disconnect the exhaust fuel addition injector connector.



    A203048
  1. Turn the retainer as shown in the illustration.



    A203049
  1. Disconnect the fuel tube from the exhaust fuel addition injector.



    A203050E02
  1. Remove the check valve and gasket.
    Text in Illustration 
    *1
    Check Valve

  1. Remove the union bolt, gasket and fuel tube.



44. REMOVE NO. 3 FUEL HOSE


    A197572
  1. Remove the No. 3 fuel hose.



45. REMOVE NO. 2 NOZZLE LEAKAGE PIPE


    A201721E01
  1. Remove the check valve and gasket.
    Text in Illustration 
    *1
    Check Valve

  1. Remove the bolt and No. 2 nozzle leakage pipe.



46. REMOVE NO. 1 NOZZLE LEAKAGE PIPE


    A203784
  1. Remove the 4 union bolts and 4 gaskets.

  1. Remove the bolt and No. 1 nozzle leakage pipe.



47. REMOVE NO. 1 NOZZLE HOLDER CLAMP


    A203042
  1. Remove the 4 bolts, 4 washers and 4 nozzle holder clamps.



48. REMOVE INJECTOR ASSEMBLY
  1. Remove the 4 injectors and 4 injection nozzle seats from the cylinder head.

  1. Remove the O-ring from each injector.

    NOTICE:
    When removing the injector assembly, store the injector in the correct order so that they can be returned to their original locations when reassembling.



49. REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY


    A197568
  1. Disconnect the 2 vacuum hoses.

  1. Remove the bolt and No. 1 vacuum transmitting pipe.



50. REMOVE VACUUM SWITCHING VALVE BRACKET


    A197569
  1. Disconnect the 2 vacuum hoses.

  1. Remove the 5 bolts and vacuum switching valve bracket.



51. REMOVE PCV HOSE


    A206318
  1. Remove the PCV hose.



52. REMOVE OIL FILLER CAP SUB-ASSEMBLY


53. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A201722E01
  1. Remove the 4 nozzle holder clamp seats, 14 bolts, nut and cylinder head cover.
    Text in Illustration 
    *1
    Bolt
    *2
    Nozzle Holder Clamp Seat
    *3
    Nut



    A201723E01
  1. Remove the cylinder head cover gasket and No. 2 cylinder head cover gasket from the cylinder head cover.
    Text in Illustration 
    *1
    Cylinder Head Cover Gasket
    *2
    No. 2 Cylinder Head Cover Gasket



54. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A201737E01
  1. Remove the 18 bolts and 2 nuts.
    Text in Illustration 
    *1
    Nut



    Z004119E06
  1. Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer, and remove the oil pan.

    NOTICE:
    1. Do not use the oil pan seal cutter for the timing chain cover side.
    2. Be careful not to damage the contact surfaces of the oil pan.



55. REMOVE OIL FILTER ELEMENT


    A094910E07
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.
    Text in Illustration 
    *1
    Oil Filter Drain Pipe
    *2
    Hose

  1. Remove the clip and open the oil filter element service cover.



    A210247
  1. Remove the oil filter drain plug.

  1. Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.



    A201803E01
  1. Install the oil filter drain pipe to the oil filter cap and drain the engine oil.
    Text in Illustration 
    *1
    Oil Filter Cap
    *2
    O-Ring
    *3
    Oil Filter Drain Pipe

  1. Remove the oil filter drain pipe.

  1. Apply a light coat of engine oil to a new O-ring and install it to the oil filter drain plug.



    A210247
  1. Install the oil filter drain plug to the oil filter cap.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    A210248E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  



    A201807E01
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand without using any tools to prevent damage to the cap O-ring groove.



56. REMOVE OIL FILTER BRACKET


    A201741
  1. Remove the 4 bolts and oil filter bracket.



    A201742
  1. Remove the gasket from the oil filter bracket.



57. REMOVE OIL STRAINER SUB-ASSEMBLY


    A201739
  1. Remove the 3 bolts and oil strainer.

  1. Remove the O-ring from the oil strainer.



58. REMOVE CAMSHAFT POSITION SENSOR


    A201744
  1. Remove the bolt and sensor.



59. DISCONNECT CRANKSHAFT POSITION SENSOR WIRE HARNESS


    A201750
  1. Using a clip remover, remove the clip.

  1. Remove the bolt and disconnect the sensor wire harness.



60. REMOVE WATER PUMP ASSEMBLY


    A202385
  1. Remove the 7 bolts, water pump and gasket.



61. REMOVE CRANKSHAFT PULLEY


  1. Set the No. 1 piston to TDC/compression.



      A202382E01
    1. Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing pointer of the timing chain cover.
      Text in Illustration 
      *1
      Timing Pointer
      *2
      Timing Mark



    A202383E01
  1. Make sure that the timing mark of the camshaft timing sprocket is at the top.
    Text in Illustration 
    *1
    Matchmark
    *2
    Timing Mark

    HINT:
    If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).

  1. Put a matchmark on the timing chain plate that is aligned with the timing mark of the camshaft timing sprocket.

    HINT:
    The timing chain has 2 yellow-colored plates. If either of them is aligned with the timing mark of the camshaft timing sprocket, this step can be omitted.



    A202384E01
  1. Turn the crankshaft by approximately 90° in the engine revolution direction from the point where the No. 1 piston is set to TDC/compression so that the lifted valve and piston do not contact each other when removing the camshaft.



    A201753E01
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt.

    SST
    09213-58014   (91551-80840)
    09330-00021  



    A201752E01
  1. Using SST, remove the pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



62. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A201754E01
  1. Remove the 13 bolts and seal washer.
    Text in Illustration 
    *1
    Bolt and Seal Washer



    A201828
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head, camshaft housing, cylinder block, stiffening crankcase and chain cover.



    A201756E01
  1. Remove the gasket and O-ring from the timing chain cover.
    Text in Illustration 
    *1
    Gasket
    *2
    O-Ring



63. REMOVE SUPPLY PUMP ASSEMBLY


    A203055
  1. Remove the 2 bolts, supply pump and No. 1 supply pump drive coupling.

  1. Remove the O-ring from the supply pump.



64. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A202386E01
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate

  1. Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.

    SST
    09240-00020   (09242-00200)



    A202387
  1. Remove the 2 bolts and No. 1 chain tensioner.



65. REMOVE CHAIN TENSIONER SLIPPER


A202388


66. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A202389
  1. Remove the 2 bolts and No. 1 chain vibration damper.



67. REMOVE CAMSHAFT TIMING SPROCKET


    A202390
  1. Remove the 4 bolts from the sprocket while holding the hexagonal portion of the No. 2 camshaft with a wrench.

  1. Remove the camshaft timing sprocket and chain.



68. REMOVE OIL PUMP DRIVE GEAR


    A202391
  1. Remove the oil pump drive gear from the crankshaft.



69. REMOVE CRANKSHAFT TIMING SPROCKET


    A202392
  1. Remove the crankshaft timing sprocket.



70. REMOVE CAMSHAFT


    A117173
  1. Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.



    A202394E01
  1. Remove the 2 union bolts.
    Text in Illustration 
    *1
    Union Bolt
    *2
    No. 4 Bearing Cap

  1. Uniformly loosen the 20 bearing cap bolts in several steps in the sequence shown in the illustration and remove the bolts.

  1. Remove the 8 bearing caps, No. 1 bearing cap and 2 oil delivery pipes.

    HINT:
    Do not remove the No. 4 bearing cap.

  1. Remove the camshaft and No. 2 camshaft.



    A202395
  1. Remove the No. 2 bearing cap.



71. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


    A202396
  1. Remove the 16 valve rocker arms.



72. REMOVE VALVE LASH ADJUSTER ASSEMBLY


    A202397
  1. Remove the 16 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.