Home › ENGINE ยท 2AD-FTV › COOLING › COOLANT

COOLANT > REPLACEMENT

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 6 bolts, 10 clips and engine under cover.



2. DRAIN ENGINE COOLANT
  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator reservoir cap.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



  1. Loosen the cylinder block drain cock plug.

    HINT:
    The plug is on the backside of the generator on the EGR cooler side.



    A208259E01


    Text in Illustration 
    *1
    Radiator Reservoir Cap
    *2
    Radiator Reservoir
    *3
    Cylinder Block Drain Cock
    *4
    Radiator Drain Cock Plug



3. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.



    A126841E01
  1. Continue adding TOYOTA SLLC until it is filled to the B line.

    HINT:
    The B line is the lower edge of the inner wall of the filler neck.

    Standard Capacity:
    Item
    Specified Condition
    w/o Combustion Type Power Heater
    7.3 liters
    (7.7 US qts, 6.4 Imp. qts)
    w/ Combustion Type Power Heater
    7.7 liters
    (8.1 US qts, 6.8 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.

  1. Start the engine, and warm it up until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Measurement Condition 
      Item
      Condition
      Manual Air Conditioning System
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Automatic Air Conditioning System
      Temperature - Toward MAX
      Air conditioning switch "OFF"

    2. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
      3. If there is not enough coolant, the engine may burn out or overheat.
      4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
      5. Until the coolant level has stabilized, run the engine at 2000 rpm.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    When pressing the radiator hoses:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the radiator fan.

  1. Stop the engine and wait until the coolant cools down to ambient temperature.



    A208266
  1. Check that the coolant level is between the FULL and LOW line.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.



4. FOR COOLANT LEAK
  1. Remove the radiator reservoir cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.



    A128571
  1. Fill the radiator with coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage.
    If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.



5. INSTALL NO. 1 ENGINE UNDER COVER
  1. Install the engine under cover with the 6 bolts and 10 clips.