AUTOMATIC TRANSAXLE FLUID > ADJUSTMENT |
| 1. PRECAUTIONS AND WORK DESCRIPTION |
The U660F automatic transaxle does not have an oil filler tube or oil level gauge. When adding fluid, add fluid into the refill hole in the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the oil pan.
Before adjusting the fluid level, add the specified amount of fluid when the engine is cold and warm up the engine to circulate the fluid in the transaxle. Ensure that the fluid temperature is as specified and the engine is idling.
The U660F automatic transaxle requires Toyota Genuine ATF WS.
Perform the adjustment according to the following procedures and notes.

| 2. WORK FLOW |
The adjustment should be performed according to the procedures referenced in the work flow below.

| 3. BEFORE FILLING TRANSAXLE WITH FLUID |
![]() |
Lift the vehicle.
Remove the No. 1 engine under cover and rear engine under cover LH.
| 4. PERFORM INITIAL FILLING |
![]() |
Remove the refill plug and gasket from the automatic transaxle.
| Operations that do not Require Initial Filling |
|
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle.
![]() |
Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Hexagon Socket Wrench |
| *3 | Overflow Plug Hole |
Perform initial filling.
![]() |
Fill the transaxle through the refill hole until fluid begins to trickle out of the overflow plug hole.
![]() |
Wait until the fluid flow slows and only drops come out.
![]() |
Temporarily install the overflow plug.
| 5. ADD SPECIFIED AMOUNT OF FLUID |
Fill the transaxle with the correct amount of fluid as listed in the table below.
| Operation Performed | Fill Amount |
| 0.5 liters (0.5 US qts, 0.4 Imp. qts) |
| 2.8 liters (3.0 US qts, 2.5 Imp. qts) |
| Removal and installation of the valve body | 3.2 liters (3.4 US qts, 2.8 Imp. qts) |
| Removal and installation of the transaxle (not including removal of the torque converter clutch) | 3.4 liters (3.6 US qts, 3.0 Imp. qts) |
| Removal and installation of the torque converter clutch (torque converter clutch reused) | 4.8 liters (5.1 US qts, 4.2 Imp. qts) |
| Installation of a new torque converter clutch | 5.3 liters (5.6 US qts, 4.7 Imp. qts) |
![]() |
Temporarily install the refill plug to avoid fluid spillage.
Lower the vehicle.
| 6. ADJUST FLUID TEMPERATURE |
When using the intelligent tester:
Connect the intelligent tester to the DLC3 with the ignition switch off.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test / Connect the TC and TE1.
Enter the following menus: Connect the TC and TE1 / ON.
Enter the following menus: A/T Oil Temperature 1.
Check the ATF temperature.
Depress and hold the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, then back to P.
![]() |
While observing the D shift indicator in the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
Enter the following menus: Connect the TC and TE1 / OFF.
Warm up the engine with the engine idling until the fluid temperature reaches the normal operating temperature (40 to 45°C [104 to 113°F]).
| Below Normal Operating Temperature | Normal Operating Temperature | Above Normal Operating Temperature |
| Below 40°C (Below 104°F) | 40 to 45°C (104 to 113°F) | Higher than 45°C (Higher than 113°F) |
| Below Normal Operating Temperature (Below 40°C) (Below 104°F) | Normal Operating Temperature (40 to 45°C) (104 to 113°F) | Above Normal Operating Temperature (Higher than 45°C) (Higher than 113°F) |
| Off | On | Blinks |
When not using the intelligent tester:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.
| *1 | DLC3 |
Depress and hold the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, then back to P.
![]() |
While observing the D shift indicator in the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
![]() |
Remove SST from terminals 13 (TC) and 4 (CG).
| *1 | DLC3 |
Allow the engine to idle until the D shift indicator comes on again.
| Below Normal Operating Temperature (Below 40°C) (Below 104°F) | Normal Operating Temperature (40 to 45°C) (104 to 113°F) | Above Normal Operating Temperature (Higher than 45°C) (Higher than 113°) |
| Off | On | Blinks |
| 7. ADJUST FLUID LEVEL |
Lift the vehicle.
Adjust the fluid level.
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket.
Check the amount of fluid that comes out of the overflow plug hole.
![]() |
*1:
If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drops come out.
![]() |
*2:
If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add transaxle fluid into the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drops come out.
![]() |
Check that the fluid flow has slowed and only drops come out.
![]() |
Install a new gasket and the overflow plug.
![]() |
Install a new gasket and the refill plug.
Lower the vehicle.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3 (when using the intelligent tester).
| 8. AFTER FILLING TRANSAXLE |
Lift the vehicle.
Clean each part.
Check for fluid leaks.
Install the No. 1 engine under cover and rear engine under cover LH.
Lower the vehicle.