SFI SYSTEM > FREEZE FRAME DATA |
| DESCRIPTION |
![]() |
| Tester Display | Measurement Item | Diagnostic Note |
| Vehicle Speed | Vehicle speed | The speed indicated on the speedometer. |
| Engine Speed | Engine speed | - |
| Calculate Load | Calculated load | The load calculated by the ECM. |
| Vehicle Load | Vehicle load | The load percentage in terms of the maximum intake air flow amount. |
| MAF | Air flow rate from Mass Air Flow (MAF) meter | If the value is approximately 0.0 g/sec.:
|
| Atmosphere Pressure | Atmospheric pressure | - |
| MAP | Intake manifold pressure | - |
| Coolant Temp | Engine coolant temperature |
|
| Intake Air | Intake air temperature |
|
| Engine Run Time | Accumulated engine running time | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start | - |
| Initial Intake Air Temp | Initial intake air temperature | - |
| Battery Voltage | Battery voltage | - |
| Accel Sens. No. 1 Volt % | Absolute accelerator pedal position according to accelerator position sensor No. 1 | - |
| Accel Sens. No. 2 Volt % | Absolute accelerator pedal position according to accelerator position sensor No. 2 | - |
| Throttle Sensor Volt % | Throttle position sensor | The throttle valve opening angle recognized by the ECM. Read the value with the ignition switch ON. |
| Throttl Sensor #2 Volt % | Throttle position sensor #2 | The throttle valve opening angle recognized by the ECM. Read the value with the ignition switch ON. |
| Throttle Sensor Position | Throttle position sensor | The calculated value based on VTA1. Read the value with the ignition switch ON. |
| Throttle Motor DUTY | Throttle actuator | - |
| Injector (Port) | Injection period of No. 1 cylinder | - |
| Injection Volum (Cylinder1) | Injection volume (cylinder 1) | The total fuel injection volume of 10 injections. |
| Fuel Pump/Speed Status | Fuel pump/status | - |
| EVAP (Purge) VSV | EVAP (purge) VSV control duty | The order signal from the ECM. |
| Evap Purge Flow | Ratio of evaporative purge flow to intake air volume | - |
| Purge Density Learn Value | Learned value of purge density | - |
| EVAP Purge VSV | VSV status for EVAP control | - |
| Target Air-Fuel Ratio | Air fuel ratio compared to stoichiometric level | - |
| AF Lambda B1 S1 | Fuel trim at A/F sensor | - |
| AFS Voltage B1 S1 | A/F sensor output voltage for bank 1 sensor 1 | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| AFS Current B1 S1 | Air fuel ratio sensor output current for bank 1 sensor 1 | - |
| O2S B1 S2 | Heated oxygen sensor output voltage for bank 1 sensor 2 | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| Short FT #1 | Short-term fuel trim of bank 1 | Short-term fuel compensation is used to maintain the air fuel ratio at the stoichiometric air fuel ratio. |
| Long FT #1 | Long-term fuel trim of bank 1 | Overall fuel compensation is carried out in the long-term to compensate for a continual deviation of the short-term fuel trim from the central value. |
| Total FT #1 | Total fuel trim of bank 1 | - |
| Fuel System Status #1 | Fuel system status (bank 1) |
|
| Fuel System Status #2 | Fuel system status (bank 2) | |
| IGN Advance | Ignition timing advance for No. 1 cylinder | - |
| Knock Feedback Value | Feedback value of knocking | - |
| Knock Correct Learn Value | Learned knocking correction value | - |
| ACIS VSV | VSV for acoustic control induction system (ACIS) | - |
| VVT Control Status #1 | VVT control (bank 1) status | - |
| VALVEMATIC Target Angle | VALVEMATIC target duration | - |
| VALVEMATIC Current Angle | Actual VALVEMATIC duration | The minimum duration is 106° CA. The maximum duration is 260° CA. |
| VALVEMATIC IG OFF | VALVEMATIC operation state | One of the items which shows the operating state of the VALVEMATIC is ON. |
| VALVEMATIC IG ON | VALVEMATIC operation state | |
| VALVEMATIC Cranking | VALVEMATIC operation state | |
| VALVEMATIC bef Warm Up | VALVEMATIC operation state | |
| VALVEMATIC aft Warm Up | VALVEMATIC operation state | |
| VALVEMATIC IDM Hi Temp | VALVEMATIC operation state | |
| VALVEMATIC Low (ACT) | VALVEMATIC operation state | |
| VALVEMATIC High (ACT) | VALVEMATIC operation state | |
| Catalyst Temp B1 S1 | Estimated catalyst temperature (for sensor 1) | - |
| Catalyst Temp B1 S2 | Estimated catalyst temperature (for sensor 2) | - |
| Starter Signal | Starter signal | - |
| Starter Control | Starter control | - |
| Power Steering Signal Record | Power steering switch status | - |
| Starter Relay | Starter relay status | - |
| Power Steer. Sig. Record | Power steering signal (history) | The signal status is usually ON until the cables are disconnected from the battery terminals. |
| ACC Relay | ACC cut relay status | - |
| Neutral Position SW Signal | Park/neutral position switch status | - |
| Clutch Switch | Clutch switch status | - |
| Stop Light Switch | Stop light switch status | - |
| A/C Signal | A/C switch status | - |
| Closed Throttle Position SW | Closed throttle position switch status | - |
| Fuel Cut Condition | Fuel-cut condition | - |
| Immobiliser Communication | Immobiliser communication | - |
| Electrical Load Signal | Electrical load signal | - |
| Time after DTC Cleared | Cumulative time after DTC cleared | - |
| Distance from DTC Cleared | Total distance vehicle driven after DTC cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared | - |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | - |
| Ignition Trig. Count | Ignition counter to calculated misfire count | - |
| Cylinder #1 Misfire Count | Misfire count of cylinder 1 | - |
| Cylinder #2 Misfire Count | Misfire count of cylinder 2 | - |
| Cylinder #3 Misfire Count | Misfire count of cylinder 3 | - |
| Cylinder #4 Misfire Count | Misfire count of cylinder 4 | - |
| All Cylinders Misfire Count | All cylinders misfire count | - |
| Misfire RPM | Average engine speed when misfire occurs | - |
| Misfire Load | Average engine load when misfire occurred | - |
| Misfire Margin | Margin to detect engine misfire | - |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention fuel cut | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention fuel cut history | - |
| Cat OT MF F/C Cylinder#1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected) | - |
| Battery Current | Battery current | Charging control service data. |
| Battery Temperature | Battery temperature | Charging control service data. |
| Alternator Output Duty | Generator output duty | Electricity generated by the alternator is output through duty ratio. Charging control service data. |
| Alt Vol - Non Active Test | Request voltage when regulator not under forced activation | The alternator regulator output voltage is output. When performing the Active Test, the value is 0 V. |
| Alt Vol - Active Test | Request voltage when regulator under forced activation | Charging control service data. When performing the Active Test, the value is 0 V. |
| Electric Fan Motor | Electric fan motor status | - |
| Idle Fuel Cut | Fuel cut idle | ON: When the throttle valve is fully closed and the engine speed is over 2800 rpm. |
| FC TAU | Fuel cut during very light load | Fuel cut is being performed with a very light load to prevent incomplete engine combustion. |