SFI SYSTEM > FREEZE FRAME DATA |
| DESCRIPTION |
![]() |
| Tester Display | Measurement Item | Diagnostic Note |
| Vehicle Speed | Vehicle speed | The speed indicated on the speedometer. |
| Engine Speed | Engine speed | - |
| Calculate Load | Calculated load | The load calculated by the ECM. |
| Vehicle Load | Vehicle load | The load percentage in terms of the maximum intake air flow amount. |
| MAF | Air flow rate from Mass Air Flow (MAF) meter | If the value is approximately 0.26 gm/sec:
|
| Atmosphere Pressure | Atmospheric pressure | - |
| MAP | Intake manifold pressure | - |
| Coolant Temp | Engine coolant temperature |
|
| Intake Air | Intake air temperature |
|
| Ambient Temperature | Ambient temperature | - |
| Engine Run Time | Accumulated engine running time | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start | - |
| Initial Intake Air Temp | Initial intake air temperature | - |
| Battery Voltage | Battery voltage | - |
| Accel Sens. No. 1 Volt % | Absolute accelerator pedal position according to accelerator position sensor No. 1 | - |
| Accel Sens. No. 2 Volt % | Absolute accelerator pedal position according to accelerator position sensor No. 2 | - |
| Throttle Sensor Volt % | Throttle position sensor | The throttle valve opening angle recognized by the ECM. Read the value with the ignition switch ON. |
| Throttl Sensor #2 Volt % | Throttle position sensor #2 | The throttle valve opening angle recognized by the ECM. Read the value with the ignition switch ON. |
| Throttle Sensor Position | Throttle sensor position | A calculated value based on VTA1. Read the value with the ignition switch ON. |
| Throttle Motor DUTY | Throttle actuator | - |
| Throttle Position | Throttle position | For use when engine stall, starting problems or rough idle is present. |
| ISC Flow | Flow rate calculated using information from each sensor | For use when engine stall, starting problems or rough idle is present. |
| ISC Position | Requested opening amount calculated using ISC control | For use when engine stall, starting problems or rough idle is present. |
| ISC Feedback Value | ISC feedback compensation amount | For use when engine stall, starting problems or rough idle is present. |
| ISC Learning Value | ISC learned compensation amount | For use when engine stall, starting problems or rough idle is present. |
| Electric Load Feedback Val | Compensation flow rate according to electrical load | For use when engine stall, starting problems or rough idle is present. |
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load | For use when engine stall, starting problems or rough idle is present. |
| Low Revolution Control | Low engine speed control operation state | For use when engine stall, starting problems or rough idle is present. |
| Neutral Control | Neutral control operation state | For use when engine stall, starting problems or rough idle is present. |
| N Range Status | Shift lever N status | For use when engine stall, starting problems or rough idle is present. |
| Eng Stall Control FB Flow | Intake air compensation flow rate | For use when engine stall, starting problems or rough idle is present. |
| Injector (Port) | Injection period of No. 1 cylinder | - |
| Injection Volum (Cylinder1) | Injection volume (cylinder 1) | The total fuel injection volume of 10 injections. |
| Fuel Pump/Speed Status | Fuel pump/status | - |
| EVAP (Purge) VSV | EVAP (purge) VSV control duty | The order signal from the ECM. |
| Evap Purge Flow | Ratio of evaporative purge flow to intake air volume | - |
| Purge Density Learn Value | Learned value of purge density | - |
| EVAP Purge VSV | VSV status for EVAP control | - |
| Purge Cut VSV Duty | Purge cut VSV duty | - |
| Target Air-Fuel Ratio | Air fuel ratio compared to stoichiometric level | - |
| AF Lambda B1 S1 | Fuel trim at A/F sensor | - |
| AFS Voltage B1 S1 | A/F sensor output voltage for bank 1 sensor 1 | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| AFS Current B1 S1 | Air fuel ratio sensor output current for bank 1 sensor 1 | - |
| A/F Heater Duty #1 | Air fuel ratio sensor heater duty ratio for bank 1 sensor 1 | - |
| O2S B1 S2 | Heated oxygen sensor output voltage for bank 1 sensor 2 | Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| O2 Heater B1 S2 | Heated oxygen sensor heater for bank 1 sensor 2 | - |
| O2 Heater Curr Val B1 S2 | Heated oxygen sensor current for bank 1 sensor 2 | - |
| Short FT #1 | Short-term fuel trim of bank 1 | Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. |
| Long FT #1 | Long-term fuel trim of bank 1 | Overall fuel compensation is carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value. |
| Total FT #1 | Total fuel trim of bank 1 | - |
| Fuel System Status #1 | Fuel system status (bank 1) |
|
| Fuel System Status #2 | Fuel system status (bank 2) | |
| IGN Advance | Ignition timing advance for No. 1 cylinder | - |
| Knock Feedback Value | Feedback value of knocking | - |
| Knock Correct Learn Value | Learned knocking correction value | - |
| Idle Spark Advn Ctrl #1 | Individual cylinder timing advance compensation amount (No. 1) | For use when the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #2 | Individual cylinder timing advance compensation amount (No. 2) | For use when the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #3 | Individual cylinder timing advance compensation amount (No. 3) | For use when the engine stalls, is difficult to start, or idles roughly. |
| Idle Spark Advn Ctrl #4 | Individual cylinder timing advance compensation amount (No. 4) | For use when the engine stalls, is difficult to start, or idles roughly. |
| ACIS VSV | VSV for acoustic control induction system (ACIS) | - |
| VVT Control Status #1 | VVT control (bank 1) status | - |
| VVT Advance Fail | VVT control failure status | - |
| VALVEMATIC Target Angle | VALVEMATIC target duration | - |
| VALVEMATIC Current Angle | Actual VALVEMATIC duration | Minimum duration: 106° CA Maximum duration: 260° CA |
| VALVEMATIC IG OFF | VALVEMATIC operation state | One of the items which shows the operating state of the VALVEMATIC is ON. |
| VALVEMATIC IG ON | VALVEMATIC operation state | |
| VALVEMATIC Cranking | VALVEMATIC operation state | |
| VALVEMATIC bef Warm Up | VALVEMATIC operation state | |
| VALVEMATIC aft Warm Up | VALVEMATIC operation state | |
| VALVEMATIC IDM Hi Temp | VALVEMATIC operation state | |
| VALVEMATIC Low (ACT) | VALVEMATIC operation state | |
| VALVEMATIC High (ACT) | VALVEMATIC operation state | |
| Catalyst Temp B1 S1 | Estimated catalyst temperature (for sensor 1) | - |
| Catalyst Temp B1 S2 | Estimated catalyst temperature (for sensor 2) | - |
| Starter Signal | Starter signal | - |
| Starter Control | Starter control | - |
| Power Steering Signal | Power steering switch status | - |
| Starter Relay | Starter relay status | - |
| Power Steer. Sig. Record | Power Steering Signal (history) | The signal status is usually ON until the cables are disconnected from the battery terminals. |
| ACC Relay | ACC cut relay status | - |
| Neutral Position SW Signal | Park/neutral position switch status | - |
| Clutch Switch | Clutch switch status | - |
| Clutch Start SW | Clutch start switch status | - |
| Stop Light Switch | Stop light switch status | - |
| A/C Signal | A/C switch status | - |
| Closed Throttle Position SW | Closed throttle position switch | - |
| Fuel Cut Condition | Fuel-cut condition | - |
| Immobiliser Communication | Immobiliser communication | - |
| Electrical Load Signal | Electrical load signal | - |
| TC Terminal | TC terminal status | - |
| Time after DTC Cleared | Cumulative time after DTC cleared | - |
| Distance from DTC Cleared | Total distance vehicle driven after DTC cleared | - |
| Warmup Cycle Cleared DTC | Warm-up cycle after DTC cleared | - |
| Dist Batt Cable Disconnect | Total distance vehicle driven after battery cable disconnected | - |
| IG OFF Elapsed Time | Cumulative time after ignition switch off | - |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | - |
| Ignition Trig. Count | Ignition counter to calculated misfire count | - |
| Cylinder #1 Misfire Count | Misfire count of cylinder 1 | - |
| Cylinder #2 Misfire Count | Misfire count of cylinder 2 | - |
| Cylinder #3 Misfire Count | Misfire count of cylinder 3 | - |
| Cylinder #4 Misfire Count | Misfire count of cylinder 4 | - |
| All Cylinders Misfire Count | All cylinders misfire count | - |
| Misfire RPM | Average engine speed when misfire occurs | - |
| Misfire Load | Average engine load when misfire occurred | - |
| Misfire Margin | Margin to detect engine misfire | - |
| Catalyst OT MF F/C | Catalyst over temperature misfire prevention fuel cut | - |
| Cat OT MF F/C History | Catalyst over temperature misfire prevention fuel cut history | - |
| Cat OT MF F/C Cylinder#1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected) | - |
| Engine Speed (Starter Off) | Engine speed when starter off | For use when engine stall, starting problems or rough idle is present. |
| Starter Count | Number of times starter turned on after ignition switch ON | For use when engine stall, starting problems or rough idle is present. |
| Run Dist of Previous Trip | Distance driven during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Engine Starting Time | Time elapsed after engine started (interval between ignition switch ON and off) | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Intake Temp | Intake air temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Engine Oil Temperature | Engine oil temperature (estimated temperature) | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Ambient Temp for A/C | Ambient temperature for A/C | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Ambient Temp | Ambient temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Engine Start Hesitation | History of hesitation during engine start | - |
| Low Rev for Eng Start | History of low engine speed after engine start | - |
| Minimum Engine Speed | Minimum engine speed | For use when engine stall, starting problems or rough idle is present. |
| Fuel Cut Elps Time | Time elapsed after engine runs at high speed | The time elapsed after a fuel cut after high engine speed has occurred (more than the rpm at which fuel cut occurs +500 rpm). |
| Battery Current | Battery current | Charging control service data. |
| Battery Temperature | Battery temperature | Charging control service data. |
| Alternator Output Duty | Generator output duty | Electricity generated by the alternator is output through duty ratio. Charging control service data. |
| Alt Vol - Non Active Test | Request voltage when regulator not under forced activation | The alternator regulator output voltage is output. When performing the Active Test, the value is 0 V. |
| Alt Vol - Active Test | Request voltage when regulator under forced activation | Charging control service data. When performing the Active Test, the value is 0 V. |
| Electric Fan Motor | Electric fan motor status | - |
| Idle Fuel Cut | Fuel cut idle | ON: When the throttle valve is fully closed and the engine speed is more than 2800 rpm. |
| FC TAU | Fuel cut during very light load | The fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete. |
| Immobiliser Fuel Cut | Status of immobiliser fuel cut | - |
| Communication with VALVEMATIC | Status of communication with VALVEMATIC system | - |
| Electrical Load Signal 1 | Electrical load signal | - |
| Electrical Load Signal 2 | Electrical load signal | - |
| SPD (NT) | Input turbine speed | - |