DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 0.2 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 4.535 V or more for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 1.75 V or less for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V, for 2 seconds when accelerator pedal depressed (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position | 0.5 to 1.1 V | 3.3 to 4.9 V |
| Throttle Position No.2 | 2.1 to 3.1 V | 4.6 to 5.0 V |

| 1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION AND THROTTLE POSITION NO.2) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position and Throttle Position No.2.
Read the values displayed on the tester.
| TP (VTA1) When Accelerator pedal Released | TP No.2 (VTA2) When Accelerator pedal Released | TP (VTA1) When Accelerator pedal Depressed | TP No.2 (VTA2) When Accelerator pedal Depressed | Trouble Area | Proceed to |
| 0 V to 0.2 V | 0 V to 0.2 V | 0 V to 0.2 V | 0 V to 0.2 V | VC circuit open | A |
| 4.5 V to 5.0 V | 4.5 V to 5.0 V | 4.5 V to 5.0 V | 4.5 V to 5.0 V | E2 circuit open | |
| 0 V to 0.2 V, or 4.5 V to 5.0 V | 2.4 V to 3.4 V (Fail-safe) | 0 V to 0.2 V, or 4.5 V to 5.0 V | 2.4 V to 3.4 V (Fail-safe) | VTA1 circuit open or ground short | |
| 0.7 V to 1.3 V (Fail-safe) | 0 V to 0.2 V, or 4.5 V to 5.0 V | 0.7 V to 1.3 V (Fail-safe) | 0 V to 0.2 V, or 4.5 V to 5.0 V | VTA2 circuit open or ground short | |
| 0.5 V to 1.1 V | 2.1 V to 3.1 V | 3.3 V to 4.9 V (Not fail-safe) | 4.6 V to 5.0 V (Not fail-safe) | TP sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the B3 throttle body connector.
Disconnect the B32 ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| VC (B3-5) - VCTA (B32-67) | Below 1 Ω |
| VTA (B3-6) - VTA1 (B32-115) | |
| VTA2 (B3-4) - VTA2 (B32-114) | |
| E2 (B3-3) - ETA (B32-91) |
| Tester Connection | Specified Condition |
| VC (B3-5) or VCTA (B32-67) - Body ground | 10 kΩ or higher |
| VTA (B3-6) or VTA1 (B32-115) - Body ground | |
| VTA2 (B3-4) or VTA2 (B32-114) - Body ground |
Reconnect the throttle body connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the B3 throttle body connector.
Turn the ignition switch on (IG).
Measure the voltage between the terminals of the throttle body connector.
| Tester Connection | Specified Condition |
| VC (B3-5) - E2 (B3-3) | 4.5 to 5.5 V |
Reconnect the throttle body connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY ASSEMBLY |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0120, P0122, P0123, P0220, P0222, P0223 and/or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||