DTC P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction |
DTC P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0120 | Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0122 | Output voltage of VTA1 is 0.2 V or less for 2 seconds (1 trip detection logic) |
|
| P0123 | Output voltage of VTA1 is 4.535 V or more for 2 seconds (1 trip detection logic) |
|
| P0220 | Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds (1 trip detection logic) |
|
| P0222 | Output voltage of VTA2 is 1.75 V or less for 2 seconds (1 trip detection logic) |
|
| P0223 | Output voltage of VTA2 is 4.8 V or more, and VTA1 is between 0.2 V and 2.02 V, for 2 seconds (1 trip detection logic) |
|
| P2135 | Either condition (a) or (b) is met (1 trip detection logic): (a) Difference between output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more (b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less, for 0.4 seconds or more |
|
| Tester Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position No. 1 | 0.5 to 1.2 V | 3.2 to 4.8 V |
| Throttle Position No. 2 | 2.0 to 2.9 V | 4.6 to 4.8 V |

| 1.READ VALUE USING THROTTLE POSITION SENSOR (THROTTLE POS AND THROTTLE POS #2) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position and Throttle Position No. 2.
Check the values displayed on the tester.
| TP#1 (VTA1) When AP Released | TP#2 (VTA2) When AP Released | TP#1 (VTA1) When AP Depressed | TP#2 (VTA2) When AP Depressed | Trouble Area | Proceed to |
| 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | VC circuit open | A |
| 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | E2 circuit open | A |
| 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 to 3.1 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 5.0 V | 2.1 to 3.1 V (Fail-safe) | VTA1 circuit open or ground short | A |
| 0.7 to 1.3 V (Fail-safe) | 0 to 2.0 V, or 4.5 to 5.0 V | 0.7 to 1.3 V (Fail-safe) | 0 to 2.0 V, or 4.5 to 5.0 V | VTA2 circuit open or ground short | A |
| 0.5 to 1.1 V | 2.1 to 3.1 V | 3.3 to 4.9 V (Not fail-safe) | 4.6 to 5.0 V (Not fail-safe) | TP sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
![]() |
Disconnect the throttle body connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VC (B3-5) - VCTA (B96-96) | Below 1 Ω |
| VTA (B3-6) - VTA1 (B96-98) | Below 1 Ω |
| VTA2 (B3-4) - VTA2 (B96-99) | Below 1 Ω |
| E2 (B3-3) - ETA (B96-97) | Below 1 Ω |
| Tester Connection | Specified Condition |
| VC (B3-5) or VCTA (B96-96) - Body ground | 10 kΩ or higher |
| VTA (B3-6) or VTA1 (B96-98) - Body ground | 10 kΩ or higher |
| VTA2 (B3-4) or VTA2 (B96-99) - Body ground | 10 kΩ or higher |
Reconnect the throttle body connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the throttle body connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VC (B3-5) - E2 (B3-3) | 4.5 to 5.0 V |
Reconnect the throttle body connector.
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY |
Replace the throttle body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0120, P0122, P0123, P0220, P0223, and/or P2135 | A |
| No output | B |
|
| ||||
| A | ||
| ||