THERMOSTAT > INSTALLATION |
| 1. INSTALL THERMOSTAT |
Install a new gasket on the thermostat.
![]() |
Install the thermostat to the water inlet housing.
| 2. INSTALL WATER INLET |
Install the water inlet with the 2 nuts.
| 3. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the wire harness clamp bracket with the bolt.
![]() |
Temporarily install the generator with the bolt.
![]() |
Temporarily install the adjusting bar with the 2 bolts.
![]() |
Install the wire harness to terminal B with the nut.
Install the terminal cap.
Connect the connector and wire harness clamp.
Install V-ribbed belt .
Adjust V-ribbed belt .
Inspect V-ribbed belt .
![]() |
Tighten the bolt.
| 4. INSTALL V-RIBBED BELT |
Temporarily install the V-ribbed belt.
| 5. ADJUST V-RIBBED BELT |
![]() |
Turn bolt C to adjust the tension of the V-ribbed belt.
Tighten bolts A and B.
| 6. INSPECT V-RIBBED BELT |
![]() |
Check the belt for wear, cracks or other signs of damage.
If any of the following defects is found, replace the V-ribbed belt.
![]() |
Check that the belt fits properly in the ribbed grooves.
![]() |
Check the V-ribbed belt deflection and tension.
| Item | Specified Condition |
| New belt | 7.0 to 8.2 mm (0.276 to 0.323 in.) |
| Used belt | 7.6 to 10.0 mm (0.299 to 0.394 in.) |
| Item | Specified Condition |
| New belt | 700 to 800 N (70 to 80 kgf, 157.4 to 179.8 lbf) |
| Used belt | 550 to 750 N (55 to 75 kgf, 123.6 to 168.6 lbf) |
| 7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 8. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
![]() |
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening until it is filled to the B line at the base of the reservoir filler neck.
| Item | Specified Condition |
| for Manual Transaxle | 5.8 liters (6.1 US qts, 5.1 Imp. qts) |
| for CVT | 6.0 liters (6.3 US qts, 5.3 Imp. qts) |
Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Condition |
| Manual Air Conditioning System | Fan speed: Any setting except off Temperature: Toward WARM Air conditioning switch: Off |
| Automatic Air Conditioning System | Temperature: Toward MAX (HOT) Air conditioning switch: Off |
Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.
Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 9. INSPECT FOR COOLANT LEAK |
Remove the radiator reservoir cap.
![]() |
Fill the radiator and reservoir with coolant, and then attach a radiator cap tester.
Warm up the engine.
Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leakage.
If there are no signs of external coolant leaks, check the heater core, cylinder block and head.
Reinstall the radiator reservoir cap.
| 10. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Attach the 4 clips to install the cover.
| 11. INSTALL RADIATOR SUPPORT OPENING COVER |
Install the radiator support opening cover with the 9 clips.
| 12. INSTALL REAR ENGINE UNDER COVER RH |
![]() |
Install the under cover with the 3 clips.
| 13. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Install the under cover with the 6 screws and 10 clips.