Label (Tester Display)
| Measurement Item/Range
| Diagnostic Note
|
Vehicle Speed
| Vehicle speed
| Speed indicated on the speedometer.
|
Engine Speed
| Engine speed
| -
|
Calculate Load
| Calculated load
| Load calculated by the ECM.
|
Vehicle Load
| Vehicle load
| -
|
MAF
| Mass air flow volume
| If the value is approximately 0.0 gm/s:
- Mass air flow meter power source circuit is open or shorted.
- VG circuit is open or shorted.
If the value is 271.0 gm/s or more:
- E2G circuit is open.
|
Atmosphere Pressure
| Atmospheric pressure
| -
|
Coolant Temp
| Engine coolant temperature
| If the value is -40°C, the sensor circuit is open. If the value is 140°C, the sensor circuit is shorted.
|
Intake Air
| Intake air temperature
| If the value is -40°C, the sensor circuit is open. If the value is 140°C, the sensor circuit is shorted.
|
Engine Run Time
| Accumulated engine running time
| -
|
Initial Engine Coolant Temp
| Initial engine coolant temperature
| -
|
Initial Intake Air Temp
| Initial intake air temperature
| -
|
Battery Voltage
| Battery voltage
| -
|
Accel Sens. No. 1 Volt %
| Absolute No. 1 accelerator pedal position
| -
|
Accel Sens. No. 2 Volt %
| Absolute No. 2 accelerator pedal position
| -
|
Throttle Sensor Volt %
| Throttle sensor position
| Read the value with the ignition switch ON (do not start engine).
|
Throttle Sensor #2 Volt %
| Throttle sensor position #2
| -
|
Throttle Sensor Position
| Throttle position
| Read the value with the ignition switch ON (do not start engine).
|
Throttle Motor DUTY
| Throttle actuator
| -
|
Throttle Position
| Throttle position
| For use when engine stall, starting problems or rough idle is present.
|
ISC Flow
| Flow rate calculated using information from each sensor
| For use when engine stall, starting problems or rough idle is present.
|
ISC Position
| Requested opening amount calculated using ISC control
| For use when engine stall, starting problems or rough idle is present.
|
ISC Feedback Value
| ISC feedback compensation amount
| For use when engine stall, starting problems or rough idle is present.
|
ISC Learning Value
| ISC learned compensation amount
| For use when engine stall, starting problems or rough idle is present.
|
Electric Load Feedback Val
| Compensation flow rate according to electrical load
| For use when engine stall, starting problems or rough idle is present.
|
Air Conditioner FB Val
| Compensation flow rate according to air conditioner load
| For use when engine stall, starting problems or rough idle is present.
|
PS Feedback Val
| Compensation flow rate according to power steering load
| For use when engine stall, starting problems or rough idle is present.
|
Low Revolution Control
| Low engine speed control operation state
| For use when engine stall, starting problems or rough idle is present.
|
Neutral Control
| Neutral control operation state
| For use when engine stall, starting problems or rough idle is present.
|
N Range Status
| Shift lever N status
| For use when engine stall, starting problems or rough idle is present.
|
Eng Stall Control FB Flow
| Intake air compensation flow rate
| For use when engine stall, starting problems or rough idle is present.
|
Deposit Loss Flow
| Deposit loss flow rate
| For use when engine stall, starting problems or rough idle is present.
|
Injector (Port)
| Injection period of No. 1 cylinder
| -
|
Injection Volum (Cylinder 1)
| Injection volume
| -
|
Fuel Pump/Speed Status
| Fuel pump status
| -
|
EVAP (Purge) VSV
| EVAP purge VSV duty ratio
| -
|
Evap Purge Flow
| Ratio of evaporative purge flow to intake air volume
| -
|
Purge Density Learn Value
| Purge density learned value
| -
|
EVAP Purge VSV
| EVAP purge VSV
| -
|
Purge Cut VSV Duty
| Purge cut VSV duty
| -
|
Target Air-Fuel Ratio
| Air-fuel ratio
| -
|
AF Lambda B1S1
| Fuel trim at air fuel ratio sensor
| -
|
AFS Voltage B1S1
| Air fuel ratio sensor output
| Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the air fuel ratio sensor.
|
AFS Current B1S1
| Air fuel ratio sensor current
| -
|
A/F Heater Duty #1
| Air fuel ratio sensor heater duty ratio
| -
|
O2S B1S2
| Heated oxygen sensor output
| Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the heated oxygen sensor.
|
O2S Impedance B1 S2
| Heated oxygen sensor impedance for bank 1 sensor 2
| -
|
O2 Heater B1S2
| Heated oxygen sensor heater
| -
|
O2 Heater Curr Val B1S2
| Heated oxygen sensor current
| -
|
Short FT #1
| Short-term fuel trim
| Short-term fuel compensation is used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
|
Long FT #1
| Long-term fuel trim
| Overall fuel compensation is carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
|
Total FT #1
| Total fuel trim
| -
|
Fuel System Status #1
| Fuel system status (Bank 1)
| - OL (Open Loop): Has not yet satisfied the conditions to go closed loop.
- CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
- OLDrive: Open loop due to driving conditions (fuel enrichment).
- OLFault: Open loop due to a detected system fault.
- CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
|
Fuel System Status #2
| Fuel system status (Bank 2)
| -
|
IGN Advance
| Ignition timing advance for No. 1 cylinder
| -
|
Knock Feedback Value
| Knocking feedback value
| -
|
Knock Correct Learn Value
| Knocking correction learned value
| -
|
Idle Spark Advn Ctrl #1
| Individual cylinder timing advance compensation amount (No. 1)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #2
| Individual cylinder timing advance compensation amount (No. 2)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #3
| Individual cylinder timing advance compensation amount (No. 3)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #4
| Individual cylinder timing advance compensation amount (No. 4)
| For use when engine stall, starting problems or rough idle is present.
|
Actual VVT Angle #1
| VVT angle status
| -
|
VVT Control Status #1
| VVT control status
| -
|
VVT Advance Fail
| VVT control failure status
| -
|
Catalyst Temp B1S1
| Catalyst temperature
| -
|
Catalyst Temp B1S2
| Catalyst temperature
| -
|
Starter Signal
| Starter signal
| -
|
Starter Control
| Starter control signal
| -
|
Power Steering Signal
| Power steering signal
| -
|
Starter Relay
| Starter Relay status
| -
|
ACC Relay
| ACC Relay status
| -
|
Neutral Position SW Signal
| Park/neutral position switch signal
| -
|
Stop Light Switch
| Stop light switch
| -
|
A/C Signal
| A/C signal
| -
|
Closed Throttle Position SW
| Closed throttle position switch
| -
|
Fuel Cut Condition
| Fuel cut condition
| -
|
TC Terminal
| TC terminal status
| -
|
Time after DTC Cleared
| Cumulative time after DTCs cleared
| -
|
Distance from DTC Cleared
| Accumulated distance driven after DTCs cleared
| -
|
Warmup Cycle Cleared DTC
| Warmup cycles after DTCs cleared
| -
|
Dist Batt Cable Disconnect
| Total distance vehicle driven after battery cable disconnected
| -
|
TC and TE1
| TC and CG (TE1) terminals of DLC3
| -
|
Ignition Trig. Count
| Ignition counter
| -
|
Cylinder #1 Misfire Count
| Cylinder #1 misfire count
| -
|
Cylinder #2 Misfire Count
| Cylinder #2 misfire count
| -
|
Cylinder #3 Misfire Count
| Cylinder #3 misfire count
| -
|
Cylinder #4 Misfire Count
| Cylinder #4 misfire count
| -
|
All Cylinders Misfire Rate
| Misfire count of all cylinders
| -
|
Misfire RPM
| Misfire RPM
| -
|
Misfire Load
| Misfire load
| -
|
Misfire Margin
| Misfire monitoring
| -
|
Catalyst OT MF F/C
| Availability of fuel-cut function to prevent misfire causing catalyst overheat
| -
|
Cat OT MF F/C History
| History of fuel-cut function to prevent misfire causing catalyst overheat
| -
|
Cat OT MF F/C Cylinder#1
| Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#2
| Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#3
| Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#4
| Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
| -
|
Engine Speed (Starter Off)
| Engine speed when starter off
| For use when engine stall, starting problems or rough idle is present.
|
Starter Count
| Number of times starter turned on after ignition switch turned to ON
| For use when engine stall, starting problems or rough idle is present.
|
Run Dist of Previous Trip
| Distance driven during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Engine Starting Time
| Time elapsed after engine started (interval between ignition switch ON and off)
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Coolant Temp
| Engine coolant temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Intake Temp
| Intake air temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Engine Oil Temperature
| Engine oil temperature (estimated temperature)
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Eng Oil Temp
| Engine oil temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Ambient Temp for A/C
| Ambient temperature for A/C
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Ambient Temp
| Ambient temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Engine Start Hesitation
| History of hesitation during engine start
| For use when engine stall, starting problems or rough idle is present.
|
Low Rev for Eng Start
| History of low engine speed after engine start
| For use when engine stall, starting problems or rough idle is present.
|
Minimum Engine Speed
| Minimum engine speed
| For use when engine stall, starting problems or rough idle is present.
|
Battery Current
| Battery current
| Charging control service data
|
Battery Temperature
| Battery temperature
| Charging control service data
|
Alternator Output Duty
| Alternator output duty
| Electricity generated by alternator is output through duty ratio Charging control service data
|
Alt Vol - Non Active Test
| Request voltage when regulator not under forced activation
| Alternator regulator output voltage is output
|
Alt Vol - Active Test
| Request voltage when regulator under forced activation
| Charging control service data
|
Electric Fan Motor
| Electric fan motor
| -
|
Idle Fuel Cut
| Fuel cut at idle
| ON: The throttle valve is fully closed and the engine speed is more than 3500 rpm.
|
FC TAU
| Fuel cut during very light load
| Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
|
Immobiliser Fuel Cut
| Status of the immobiliser fuel cut
| -
|
Electrical Load Signal 1
| Electrical load signal
| -
|
Electrical Load Signal 3
| Electrical load signal
| -
|