ENGINE UNIT > REASSEMBLY |
| 1. INSTALL PISTON WITH PIN SUB-ASSEMBLY |
![]() |
Using a screwdriver, install a new snap ring at one end of the piston pin hole.
![]() |
Gradually heat the piston to approximately 80°C (176°F).
Coat the piston pin with engine oil.
![]() |
Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.
![]() |
Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
![]() |
Using a screwdriver, install a new snap ring at the other end of the piston pin hole.
| 2. INSTALL PISTON RING SET |
Install the oil ring expander and 2 side rails by hand.
![]() |
Using a piston ring expander, install the 2 compression rings so that the painted marks are positioned as shown in the illustration.
![]() |
Position the piston rings so that the ring ends are as shown in the illustration.
| 3. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, install the 3 oil nozzles with the bolts.
| 4. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY |
![]() |
Apply adhesive around the drain cocks.
Install the cylinder block water drain cocks.
Temporarily install the drain cocks.
![]() |
Within one full rotation, tighten the drain cock to the angle shown in the illustration.
Install the water drain cock plug to the water drain cocks.
| 5. INSTALL CRANKSHAFT BEARING |
![]() |
Clean the main journal and both surfaces of the bearing.
Install the upper bearing.
![]() |
Install the upper bearing to the cylinder block as shown in the illustration.
Install the lower bearing.
![]() |
Install the lower bearing to the bearing cap.
Using a vernier caliper, measure the distance between the bearing cap's edge and the lower bearing's edge.
| 6. INSTALL CRANKSHAFT |
![]() |
Install the 2 thrust washers under the No. 2 journal position of the cylinder block with the oil grooves facing outward.
Apply engine oil to the upper bearing, and then place the crankshaft on the cylinder block.
![]() |
Confirm the front marks and numbers of the main bearing caps and install the bearing caps on the cylinder block.
Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.
Temporarily install the 8 main bearing cap bolts to the inside positions.
![]() |
Insert the main bearing cap by hand until the clearance between the main bearing cap and the cylinder block is less than 6 mm (0.23 in.) by marking the 2 internal bearing cap bolts as a guide.
![]() |
Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.
Apply a light coat of engine oil to the threads and under the heads of the 8 main bearing cap bolts.
![]() |
Install the 8 main bearing cap bolts to the outside positions.
Install the crankshaft bearing cap bolts.
Step 1
![]() |
Install and uniformly tighten the 16 main bearing cap bolts in the sequence shown in the illustration.
Step 2
![]() |
Mark the front of the bearing cap bolts with paint.
Tighten the bearing cap bolts another 90° in the order shown in step 1.
Check that the painted mark is now at a 90° angle from the front.
Check that the crankshaft turns smoothly.
![]() |
Install and uniformly tighten the 8 main bearing cap bolts in several steps, in the sequence shown in the illustration.
Check that the crankshaft turns smoothly.
| 7. INSTALL CONNECTING ROD BEARING |
Install the connecting rod bearing to the connecting rod and bearing cap.
![]() |
Using a vernier caliper, measure the distance between the connecting rod's and bearing cap's edges, and each connecting rod bearing's edge.
| 8. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.
![]() |
Position the piston rings so that the ring ends are as shown in the illustration.
![]() |
Using a piston ring compressor, push the correctly numbered piston and connecting rod into the cylinder with the front mark of the piston facing forward.
![]() |
Check that the front mark of the connecting rod cap is facing forward.
Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.
Install the connecting rod cap bolts.
Step 1
![]() |
Install and alternately tighten the bolts of the connecting rod cap in several steps.
Step 2
![]() |
Mark the front side of each connecting cap bolt with paint.
Retighten the cap bolts 90° as shown in the illustration.
Check that the painted mark is now at a 90° angle from the front.
Check that the crankshaft turns smoothly.
| 9. INSTALL CRANK POSITION SENSOR |
![]() |
Install the crank position sensor with the bolt.
| 10. INSTALL NO. 2 STRAIGHT SCREW PLUG |
![]() |
Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.
| 11. INSTALL NO. 1 STRAIGHT SCREW PLUG |
![]() |
Using a 10 mm hexagon wrench, install 4 new gaskets and the straight screw plugs.
| 12. INSTALL VALVE SPRING SEAT |
Install the valve spring seats to the cylinder head.
| 13. INSTALL VALVE STEM OIL SEAL |
![]() |
Apply a light coat of engine oil to new oil seals.
![]() |
Using SST, push in the oil seals.
| 14. INSTALL INTAKE VALVE |
![]() |
Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.
Install the valve, compression spring and spring retainer to the cylinder head.
![]() |
Using SST and wooden blocks, compress the spring and install the retainer lock.
![]() |
Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
| 15. INSTALL EXHAUST VALVE |
![]() |
Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.
Install the valve, compression spring and spring retainer to the cylinder head.
![]() |
Using SST and wooden blocks, compress the spring and install the retainer lock.
![]() |
Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
| 16. INSTALL VALVE STEM CAP |
Apply a light coat of engine oil to the valve stem caps.
Install the valve stem caps to the cylinder head.
| 17. INSTALL WATER INLET PIPE |
![]() |
Install the water inlet pipe with the 2 bolts.
Install the water by-pass hose.
| 18. INSTALL CYLINDER HEAD SUB-ASSEMBLY (for Bank 1) |
Check the piston protrusions for each cylinder.
Clean the cylinder block with solvent.
Set the piston of the cylinder to be measured to slightly before TDC.
![]() |
Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp facing upward.
Place the cylinder head on the cylinder block.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
Step 1
![]() |
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps, in the sequence shown in the illustration.
Step 2
![]() |
Mark the cylinder head bolt head with paint as shown in the illustration.
Tighten the cylinder heads bolts another 90° in the sequence shown in step 1.
Step 3
Tighten the cylinder head bolts by an additional 90° in the sequence shown in step 1.
Check that the painted mark is now facing rearward.
| 19. INSTALL CYLINDER HEAD SUB-ASSEMBLY (for Bank 2) |
Check the piston protrusions for each cylinder.
Clean the cylinder block with solvent.
Set the piston of the cylinder to be measured to slightly before TDC.
![]() |
Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp facing upward.
Place the cylinder head on the cylinder block.
Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.
Step 1
![]() |
Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps, in the sequence shown in the illustration.
Step 2
![]() |
Mark the cylinder head bolt heads with paint as shown in the illustration.
Tighten the cylinder head bolts another 90° in the sequence shown in step 1.
Step 3
Tighten the cylinder head bolts by an additional 90° in the sequence shown in step 1.
Check that the painted mark is now facing rearward.
![]() |
Install the 2 bolts in the order shown in the illustration.
| 20. INSTALL VALVE LASH ADJUSTER ASSEMBLY |
Be sure to inspect the valve lash adjuster before installing it .
Install the lash adjusters.
| 21. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
Apply engine oil to the lash adjuster tips and valve stem cap ends.
![]() |
Make sure that the valve rocker arms are installed as shown in the illustration.
| 22. INSTALL NO. 1 CAMSHAFT |
Apply engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 1 camshaft to the camshaft housing.
| 23. INSTALL NO. 2 CAMSHAFT |
Apply engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 2 camshaft to the camshaft housing.
| 24. INSTALL CAMSHAFT BEARING CAP (for Bank 1) |
![]() |
Confirm the marks and numbers on the camshaft bearing caps and place them each in their proper position and direction.
![]() |
Temporarily install the 8 bolts in the order shown in the illustration.
| 25. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY (for Bank 1) |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the camshaft housing, and install the 12 bolts in the order shown in the illustration.
![]() |
Tighten the 8 bolts in the order shown in the illustration.
![]() |
Install 3 new gaskets.
| 26. INSTALL NO. 3 CAMSHAFT |
Apply engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 3 camshaft to the camshaft housing.
| 27. INSTALL NO. 4 CAMSHAFT |
Apply engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 4 camshaft to the camshaft housing.
| 28. INSTALL CAMSHAFT BEARING CAP (for Bank 2) |
![]() |
Confirm the marks and numbers on the camshaft bearing caps and place them each in their proper position and direction.
![]() |
Temporarily install the 8 bolts in the order shown in the illustration.
| 29. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY (for Bank 2) |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the camshaft housing and tighten the 13 bolts in the order shown in the illustration.
![]() |
Tighten the 8 bolts in the order shown in the illustration.
![]() |
Install 3 new gaskets.
| 30. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the chain tensioner with the bolt.
While pushing in the tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it in place.
| 31. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1) |
![]() |
Align the mark plates (yellow) with the timing marks (1 dot mark) of the camshaft timing gears as shown in the illustration.
Apply a small amount of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear. Install the camshaft timing gear and camshaft timing exhaust gear with the No. 2 chain installed.
![]() |
Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts.
Remove the pin from the No. 2 chain tensioner.
| 32. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the chain tensioner with the bolt.
While pushing in the tensioner, insert a pin of φ1.0 mm (0.039 in.) into the hole to fix it in place.
| 33. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2) |
![]() |
Align the mark plates (yellow) with the timing marks (2 dot mark) of the camshaft timing gears as shown in the illustration.
Apply a small amount of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear. Install the camshaft timing gear and camshaft timing exhaust gear with the No. 2 chain installed.
![]() |
Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts.
Remove the pin from the No. 2 chain tensioner.
| 34. INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET |
![]() |
Install the timing gear set keys and timing gear as shown in the illustration.
| 35. INSTALL NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Install the chain vibration damper with the 2 bolts.
| 36. INSTALL NO. 2 CHAIN VIBRATION DAMPER |
Install the 2 chain vibration dampers.
| 37. INSTALL IDLE SPROCKET ASSEMBLY |
Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.
![]() |
Temporarily install the No. 1 idle gear shaft and idle sprocket with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.
Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.
| 38. INSTALL NO. 1 CHAIN SUB-ASSEMBLY |
![]() |
Align the mark plates and timing marks as shown in the illustration and install the chain.
![]() |
Turn the camshaft timing gear on the bank 1 counterclockwise to tighten the chain between the banks.
![]() |
Align the mark plate and timing mark as shown in the illustration and install the chain onto the crankshaft timing gear.
Temporarily tighten the pulley set bolt.
![]() |
Turn the crankshaft clockwise to set it to the bank 1 block bore center line (TDC / compression).
| 39. INSTALL CHAIN TENSIONER SLIPPER |
Install the chain tensioner slipper.
| 40. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
![]() |
Install the chain tensioner with the 2 bolts.
![]() |
Remove the lock pin of the chain tensioner. Check that each timing mark is aligned with the crankshaft at the TDC / compression.
Remove the pulley set bolt.
| 41. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Install a new gasket.
![]() |
Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration.
Apply seal packing in a continuous bead to the engine unit as shown in the illustration.

Apply seal packing in a continuous line to the timing chain cover as shown in the illustration.

| Position | Specified Condition |
| A - A | 6.0 mm (0.236 in.) |
| B - B | 6.5 mm (0.256 in.) |
| Continuous line area | 4.5 mm (0.177 in.) or more |
| Dashed line area | 3.5 mm (0.138 in.) or more |
| Alternate long and short dashed line area | 3.5 mm (0.138 in.) or more |
Temporarily install the timing chain cover with the 23 bolts and 2 nuts.

Tighten the bolts in this order: Area 1, Area 2, Area 3, Area 4.
| 42. INSTALL WATER PUMP ASSEMBLY |
![]() |
Install a new water pump gasket and the water pump with the 16 bolts.
| 43. INSTALL ENGINE REAR OIL SEAL RETAINER |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the oil seal retainer with the 6 bolts.
| 44. INSTALL CRANKSHAFT PULLEY |
![]() |
Align the pulley set key with the key groove of the pulley, and slide on the pulley.
Using SST, install the pulley bolt.
| 45. INSTALL NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Install the oil pan baffle plate with the 7 bolts.
| 46. INSTALL OIL PAN SUB-ASSEMBLY |
![]() |
Install 2 new O-rings to the timing chain cover.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the oil pan with the 16 bolts and 2 nuts.
| 47. INSTALL OIL STRAINER SUB-ASSEMBLY |
![]() |
Install a new gasket and the oil strainer with the bolt and 2 nuts.
| 48. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Install the oil pan with the 16 bolts and 2 nuts.
Install a new gasket and the drain plug.
| 49. INSTALL OIL FILTER ELEMENT |
Clean the oil filter cap threads and O-ring groove.
![]() |
Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
Set a new oil filter element in the oil filter cap.
| 50. INSTALL OIL FILTER CAP ASSEMBLY |
Remove any dirt or foreign matter from the installation surface and inside of the engine.
Apply a small amount of engine oil to the O-ring again and install the oil filter cap.
![]() |
Using SST, tighten the oil filter cap.
![]() |
Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
Install the oil filter drain plug to the filter cap.
| 51. INSTALL WATER INLET HOUSING |
![]() |
Install 2 new O-rings.
![]() |
Install the water inlet with the 2 bolts and nut.
Connect the No. 1 water by-pass hose.
Apply adhesive around the drain cock.
Install the drain cock to the water inlet housing.
Install the drain cock plug to the water drain cock.
Install a new gasket to the thermostat.
![]() |
Align the thermostat jiggle valve with the upper stud bolt, and insert the thermostat in the water inlet housing.
![]() |
Install the water inlet with the 2 nuts.
| 52. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET |
![]() |
Install the engine mounting bracket with the 6 bolts.
| 53. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1) |
![]() |
Apply seal packing as shown in the illustration.
Install a new gasket to the head cover.
![]() |
Install the head cover with the 12 bolts in the order shown in the illustration.
| 54. INSTALL OIL PIPE |
![]() |
Make sure that there is no foreign matter on the mesh of the oil control valve filter.
Install the oil control valve filter to the oil pipe union. Install 2 new gaskets and temporarily install the oil pipe (on the head cover side) with the oil pipe union.
Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil pipe union.
Install bolt A to the cylinder head.
Tighten the 2 oil pipe union bolts.
| 55. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2) |
![]() |
Apply seal packing as shown in the illustration.
Install a new gasket to the head cover.
![]() |
Install the head cover with the 12 bolts in the order in the illustration.
| 56. INSTALL NO. 1 OIL PIPE |
![]() |
Make sure that there is no foreign matter on the mesh of the oil control valve filter.
Install the oil control valve filter to the oil pipe union. Install 2 new gaskets and temporarily install the oil pipe (on the head cover side) with the oil pipe union.
Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil pipe union.
Tighten the 2 oil pipe union bolts.
| 57. INSTALL WATER OUTLET |
![]() |
Install 2 new gaskets and a new O-ring.
Apply soapy water to the O-ring.
![]() |
Install the water outlet with the 2 bolts and 4 nuts.
| 58. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Install the 4 camshaft timing oil control valves with the 4 bolts.
| 59. INSTALL CAMSHAFT POSITION SENSOR |
![]() |
Install the 4 camshaft position sensors with the 4 bolts.
| 60. INSTALL VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Apply adhesive to 2 or 3 threads of the ventilation valve.
![]() |
Install the ventilation valve sub-assembly.
| 61. INSTALL OIL PAN DRAIN PLUG |
![]() |
Install the drain plug and gasket.
| 62. INSTALL SPARK PLUG |
Install the 6 spark plugs.
| 63. INSTALL OIL FILLER CAP SUB-ASSEMBLY |
Install the oil filler cap sub-assembly.