Home › ENGINE · 2GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic):
  1. (a) Vehicle speed more than 20 km/h (12.4 mph)
  2. (b) Engine speed more than 1000 rpm
  3. (c) STA signal ON
  1. Park/Neutral Position (PNP) switch
  2. ST relay circuit
  3. Ignition switch
  4. ECM

WIRING DIAGRAM


A172783E01


INSPECTION PROCEDURE

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
    If the engine will not crank, proceed to the problem symptoms table (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG).

  1. Check the result when the engine starts.

    Standard:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    On (IG)
    OFF
    Engine Starts
    ON

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
CHECK INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY


    A107908E01
  1. Disconnect the PNP switch connector.

  1. Measure the resistance when the transmission gear selector lever is moved to each position.

    Standard resistance:
    Gear Selector
    Lever Position
    Tester Connection
    Specified Condition
    P
    2 - 6, 4 - 5
    Below 1 Ω
    R
    1 - 2
    N
    2 - 9, 4 - 5
    D
    2 - 7

  1. Reconnect the PNP switch connector.



OK
Go to step 5
NG


3.REPLACE PARK / NEUTRAL POSITION SWITCH ASSEMBLY

NEXT


4.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG).

  1. Check the result when the engine starts.

    Standard:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    On
    OFF
    Engine Starts
    ON



OK
SYSTEM OK
NG


5.INSPECT IGNITION SWITCH ASSEMBLY


    A056879E31
  1. Disconnect the ignition switch connector.

  1. Measure the resistance.

    Standard resistance:
    Ignition Switch Position
    Tester Connection
    Specified Condition
    LOCK
    All Terminals
    10 kΩ or higher
    ACC
    2 - 3
    Below 1 Ω
    ON
    2 - 3, 2 - 4, 6 - 7
    START
    1 - 2, 2 - 4, 6 - 7, 7 - 8

  1. Reconnect the ignition switch connector.



OK
Go to step 7
NG


6.REPLACE IGNITION SWITCH ASSEMBLY

NEXT


7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the ignition switch is turned on (IG).

  1. Check the result when the engine starts.

    Standard:
    Ignition Switch Condition
    Tester Display (Starter Signal)
    On
    OFF
    Engine Starts
    ON



OK
SYSTEM OK
NG


8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)

NEXT


9.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the tester on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle at more than 20 km/h (12.4 mph) for over 20 seconds.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0617
    A
    No DTC
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)