DTC P0617 Starter Relay Circuit High |
| w/ Entry and Start System |

| w/o Entry and Start System |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0617 | When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic):
|
|


| 1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM |
| Result | Proceed to |
| w/o Entry and Start System | A |
| w/ Entry and Start System | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | OFF |
| START | ON |
| Result | Proceed to |
| OK | A |
| NG (A/T Model) | B |
| NG (M/T Model) | C |
|
| ||||
|
| ||||
| B | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the B28 PNP switch connector.
Measure the resistance when the transmission gear selector lever is moved to each position.
| Gear Selector Lever Position | Tester Connection | Specified Condition |
| P | 2 - 6, 4 - 5 | Below 1 Ω |
| R | 1 - 2 | |
| N | 2 - 9, 4 - 5 | |
| D | 2 - 7 | |
| 2 | 2 - 3 | |
| L | 2 - 8 |
Reconnect the PNP switch connector.
|
| ||||
| NG | |
| 4.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
| NEXT | |
| 5.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | OFF |
| START | ON |
|
| ||||
| NG | |
| 6.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the E5 ignition switch connector.
Measure the resistance.
| Ignition Switch Position | Tester Connection | Specified Condition |
| LOCK | All Terminals | 10 kΩ or higher |
| ACC | 2 - 3 | Below 1 Ω |
| ON | 2 - 3, 2 - 4, 6 - 7 | |
| START | 1 - 2, 2 - 4, 6 - 7, 7 - 8 |
Reconnect the ignition switch connector.
|
| ||||
| NG | |
| 7.REPLACE IGNITION SWITCH ASSEMBLY |
| NEXT | |
| 8.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | OFF |
| START | ON |
|
| ||||
| NG | |
| 9.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM [A/T MODEL], IGNITION SWITCH - STA TERMINAL OF ECM [M/T MODEL]) |
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Drive the vehicle at more than 12.4 mph (20 km/h) for over 20 seconds.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0617 | A |
| No DTC | B |
|
| ||||
| A | ||
| ||
| 11.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the tester when the ignition switch is turned to the on (IG) and START positions.
| Ignition Switch Position | Starter Signal |
| on (IG) | OFF |
| Engine start | ON |
|
| ||||
| NG | |
| 12.INSPECT PARK / NEUTRAL POSITION SWITCH OR CLUTCH START SWITCH |
![]() |
Inspect the Park/Neutral Position (PNP) switch (for A/T models).
Disconnect the B28 PNP switch connector.
Measure the resistance when the transmission gear selector lever is moved to each position.
| Gear Selector Lever Position | Tester Connection | Specified Condition |
| P | 2 - 6, 4 - 5 | Below 1 Ω |
| R | 1 - 2 | |
| N | 2 - 9, 4 - 5 | |
| D | 2 - 7 | |
| 2 | 2 - 3 | |
| L | 2 - 8 |
Reconnect the PNP switch connector.
![]() |
Inspect the clutch start switch (for M/T models).
Disconnect the A4 clutch start switch connector.
Measure the resistance when the clutch start switch is ON and OFF.
| Switch Position | Tester Connection | Specified Condition |
| on (pushed) | 1 - 2 | Below 1 Ω |
| off (free) | 1 - 2 | 10 kΩ or higher |
Reconnect the clutch start switch connector.
|
| ||||
| OK | ||
| ||