Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the front seat frame assembly (w/ adjuster) may injure your hands.

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. REMOVE VERTICAL ADJUSTER COVER LH (for Driver Side)


    B131224
  1. Using a screwdriver, detach the 2 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    B131225
  1. Remove the 2 screws and handle.



3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH (for Driver Side)


    B131223
  1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH (for Front Passenger Side)

HINT:
Use the same procedures described for the driver side.



5. REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side)


    B210577
  1. Disconnect the rubber band of the front seatback board or front seatback cover from the front seat frame assembly (w/ adjuster).



    B131226
  1. Remove the 2 screws.

  1. Using a screwdriver, detach the 3 claws and remove the cushion shield.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)


    B210577
  1. Disconnect the rubber band of the front seatback board or front seatback cover from the front seat frame assembly (w/ adjuster).



    B131227E01
  1. Remove the 2 screws.

  1. Using a screwdriver, detach the 3 claws and remove the cushion shield.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE FRONT SEAT CUSHION INNER SHIELD LH


    B131228
  1. Remove the screw.

  1. Using a screwdriver, detach the claw and clip. Then remove the inner shield.

    HINT:
    Tape the screwdriver tip before use.



8. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. for Driver Seat:
    Disconnect the 2 connectors and detach the 3 clamps.

  1. for Passenger Seat:
    Disconnect the 2 connectors and detach the 3 clamps.



    B133640
  1. Remove the nut and seat belt.



9. REMOVE FRONT SEAT CUSHION COVER


B131230E01
  1. w/ Seat Heater System:
    Disconnect the 2 connectors.

  1. Using a clip remover, remove the 2 clips.

  1. Detach the 2 hooks on the front side of the seat cushion.

  1. Using a screwdriver, detach the hooks and remove the seat cushion cover (with pad).

    HINT:
    Tape the screwdriver tip before use.



    B131232E01
  1. Remove the 15 hog rings and seat cushion cover from the seat cushion pad.



10. REMOVE FRONT SEAT CUSHION HEATER (w/ Seat Heater System)


    B134550E01
  1. Cut off the 10 tack pins which fasten the seat heater, and then remove the seat cushion heater from the seat cushion cover.

    NOTICE:
    Be careful not to damage the seat cushion cover and seat heater.



11. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)


    B131245
  1. Open the lower part of the seatback board. Then remove the 2 screws.



    B131244
  1. Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.



12. REMOVE FRONT SEATBACK COVER


    B131240E01
  1. w/ Seatback Board:
    Remove the 5 hog rings.

  1. w/ Seatback Board:
    Using a screwdriver, detach the hooks.

    NOTICE:
    Tape the screwdriver tip before use.



    B131239E01
  1. w/o Seatback Board:
    Open the 2 zippers.



    B131238E01
  1. w/o Seatback Board:
    Lift up the seatback cover and remove the 3 hog rings.



    B185902
  1. w/ Active Headrest:

    1. Detach the 4 claws and remove the 2 front seat headrest supports.



    B060977E01
  1. w/o Active Headrest:

    1. Detach the 4 claws and remove the 2 front seat headrest supports.



    B131236
  1. w/ Front Seat Side Airbag:
    Remove the nut and move the 2 seatback cover brackets.

  1. Remove the seatback cover (with pad) from the front seat frame assembly (w/ adjuster).



    B131241E01
  1. Remove the 11 hog rings and seatback cover from the seatback pad.



13. REMOVE FRONT SEATBACK HEATER (w/ Seat Heater System)


    B131243E01
  1. Cut off the 6 tack pins which fasten the seat heater, and then remove the seat cushion heater from the seat cushion cover.

    NOTICE:
    Be careful not to damage the seat cushion cover and seat heater.



14. REMOVE FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)


    B257725E02
  1. Disengage the 5 clamps and disconnect the wire harness.



    B257260
  1. Disengage the 2 clamps and disconnect the wire harness.

  1. Remove the 2 nuts and front seat side airbag assembly LH.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



15. REMOVE LOWER ACTIVE HEADREST UNIT (w/ Active Headrest)


B208413
  1. Remove the nut.

  1. Detach the clamp.



    B210601
  1. Detach the clamp.

  1. Remove the 2 nuts and lower active headrest unit.



16. REMOVE UPPER ACTIVE HEADREST UNIT (w/ Active Headrest)


B210602
  1. Remove the 4 nuts and upper active headrest unit.



17. REMOVE RECLINING ADJUSTER LOWER INSIDE COVER LH


    B131247
  1. Remove the screw.

  1. Detach the claw and remove the inside cover.



18. REMOVE RECLINING ADJUSTER LOWER INSIDE COVER RH

HINT:
Use the same procedures described for the LH side.



19. REMOVE RECLINING ADJUSTER UPPER INSIDE COVER LH


    B131248
  1. Remove the screw and inside cover.



20. REMOVE RECLINING ADJUSTER UPPER INSIDE COVER RH
  1. Remove the screw and inside cover.



21. REMOVE FRONT SEAT CUSHION LOWER SHIELD LH


    B131249E01
  1. Using a screwdriver, detach the claw and remove the lower shield.

    HINT:
    Tape the screwdriver tip before use.



22. REMOVE FRONT SEAT CUSHION LOWER SHIELD RH

HINT:
Use the same procedures described for the LH side.



23. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)


    B127917E01
  1. Remove the seat slide position sensor protector from the seat position sensor.

  1. Using a T30 "torx" socket, remove the "torx" screw and seat position sensor.

  1. Disconnect the connector.



24. REMOVE FRONT INNER SEAT TRACK ASSEMBLY LH


B208429
  1. Using a T50 "TORX" socket, remove the 2 bolts and inner seat track bracket.



  1. Using a T40 "TORX" socket, remove the 8 bolts and front seat frame assembly (w/ adjuster).


    B208430



    B180774
  1. Using a screwdriver, detach the 2 springs and remove the seat track adjusting handle as shown in the illustration.



25. REMOVE FRONT OUTER SEAT TRACK ASSEMBLY LH