FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY |
| 1. REMOVE RECLINING POWER SEAT SWITCH KNOB |
![]() |
Using a screwdriver, detach the knob.
| 2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Using a screwdriver, detach the knob.
| 3. REMOVE FRONT SEAT CUSHION SHIELD LH |
![]() |
Disconnect the rubber band of the front seatback board from the front seat frame assembly (w/ adjuster).
![]() |
Remove the 5 screws.
Using a screwdriver, detach the 3 claws and remove the cushion shield (with front No. 1 seat cushion inner shield).
Disconnect the connector from the front power seat lumbar switch.
![]() |
Remove the front No. 1 seat cushion inner shield from the cushion shield.
Remove the screw.
Using a screwdriver, detach the claw and remove the inner shield.
| 4. REMOVE FRONT POWER SEAT LUMBAR SWITCH |
![]() |
Remove the 2 screws and switch.
| 5. REMOVE FRONT SEAT CUSHION INNER SHIELD LH |
![]() |
Remove the screw.
Using a screwdriver, detach the 3 claws.
Using a clip remover, detach the clip and remove the inner shield.
| 6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
for Driver Seat:
Disconnect the 2 connectors and detach the 2 clamps.
for Passenger Seat:
Disconnect the connector and detach the 2 clamps.
![]() |
Remove the nut and seat belt.
| 7. REMOVE FRONT POWER SEAT SWITCH |
![]() |
Remove the 3 screws.
Disconnect the connector and remove the switch.
| 8. REMOVE FRONT SEAT CUSHION COVER |
![]() |
w/ Seat Heater System:
Disconnect the 2 connectors.
Using a clip remover, remove the 2 clips.
Detach the 2 hooks on the front side of the seat cushion.
Using a screwdriver, detach the hooks and remove the seat cushion cover (with pad).
![]() |
Remove the 15 hog rings and seat cushion cover from the seat cushion pad.
| 9. REMOVE FRONT SEAT CUSHION HEATER |
![]() |
Cut off the 10 tack pins which fasten the seat heater to the seat cushion cover, and then remove the seat cushion heater from the seat cushion cover.
| 10. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH |
![]() |
Open the lower part of the seatback board. Then remove the 2 screws.
![]() |
Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.
| 11. REMOVE FRONT SEATBACK COVER |
![]() |
Remove the 5 hog rings.
Using a screwdriver, detach the hooks.
![]() |
w/ Active Headrest:
Detach the 4 claws and remove the 2 headrest supports.
![]() |
w/o Active Headrest:
Detach the 4 claws and remove the 2 headrest supports.
![]() |
w/ Front Seat Side Airbag:
Remove the nut and move the 2 seatback cover brackets.
Remove the seatback cover (with pad) from the front seat frame assembly (w/ adjuster).
![]() |
Remove the 11 hog rings and seatback cover from the seatback pad.
| 12. REMOVE FRONT SEATBACK HEATER |
![]() |
Cut off the 6 tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.
| 13. REMOVE FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag) |
![]() |
Disengage the 5 clamps and disconnect the wire harness.
![]() |
Disengage the 2 clamps and disconnect the wire harness.
Remove the 2 nuts and front seat side airbag assembly LH.
| 14. REMOVE LOWER ACTIVE HEADREST UNIT (w/ Active Headrest) |
![]() |
Remove the nut.
Detach the clamp.
![]() |
Detach the clamp.
Remove the 2 nuts and lower active headrest unit.
| 15. REMOVE UPPER ACTIVE HEADREST UNIT (w/ Active Headrest) |
![]() |
Remove the 4 nuts and upper active headrest unit.
| 16. REMOVE RECLINING ADJUSTER LOWER INSIDE COVER LH |
![]() |
Remove the 2 screws.
Detach the claw and remove the inside cover.
| 17. REMOVE RECLINING ADJUSTER LOWER INSIDE COVER RH |
| 18. REMOVE RECLINING ADJUSTER UPPER INSIDE COVER LH |
![]() |
Remove the screw and inside cover.
| 19. REMOVE RECLINING ADJUSTER UPPER INSIDE COVER RH |
Remove the screw and inside cover.
| 20. REMOVE FRONT SEAT CUSHION LOWER SHIELD LH |
![]() |
Remove the screw.
Detach the hook of the lower shield and remove the lower shield.
| 21. REMOVE FRONT SEAT CUSHION LOWER SHIELD RH |
| 22. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 2 screws and lumbar support adjuster.
| 23. REMOVE BUSH |
![]() |
Remove the bush.
| 24. REMOVE POWER SEAT MOTOR ASSEMBLY |
![]() |
Remove the 3 screws and power seat motor.
| 25. REMOVE SEAT POSITION AIRBAG SENSOR |
![]() |
Remove the seat slide position sensor protector from the seat position sensor.
Using a T30 "torx" socket, remove the "torx" screw and seat position sensor.
Disconnect the connector.
| 26. REMOVE FRONT SEAT WIRE |