Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame (with adjuster) may injure your hands.

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. INSTALL FRONT SEAT WIRE


2. INSTALL SEAT POSITION AIRBAG SENSOR
  1. Using a 1 mm (0.039 in.) feeler gauge, install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm to 1.4 mm (0.023 to 0.055 in.).

  1. Using a T30 "torx" socket, tighten the "torx" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm to 1.4 mm (0.023 to 0.055 in.).

  1. Connect the connector.



    B127917E03
  1. Install the seat slide position sensor protector to the seat position sensor.



3. INSTALL POWER SEAT MOTOR ASSEMBLY


B210584
  1. Install the power seat motor with the 3 screws.



4. INSTALL BUSH


B210585
  1. Install the bush.



5. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY


    B131284E01
  1. Install the lumbar support adjuster with the 2 screws.

  1. Connect the connector.



6. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH


    B122088
  1. Attach the hook of the lower shield.

  1. Install the lower shield with the screw.



7. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH

HINT:
Use the same procedures described for the LH side.



8. INSTALL RECLINING ADJUSTER UPPER INSIDE COVER LH


    B131286
  1. Install the inside cover with the screw.



9. INSTALL RECLINING ADJUSTER UPPER INSIDE COVER RH
  1. Install the inside cover with the screw.



10. INSTALL RECLINING ADJUSTER LOWER INSIDE COVER LH


    B131285
  1. Attach the claw to install the inside cover.

  1. Install the 2 screws.



11. INSTALL RECLINING ADJUSTER LOWER INSIDE COVER RH

HINT:
Use the same procedures described for the LH side.



12. INSTALL UPPER ACTIVE HEADREST UNIT (w/ Active Headrest)


B210602
  1. Install the upper active headrest unit with the 4 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



13. INSTALL LOWER ACTIVE HEADREST UNIT (w/ Active Headrest)


B210601
  1. Install the lower active headrest unit with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Attach the clamp.



    B208413
  1. Attach the clamp.

  1. Install the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



14. INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



    B257260
  1. Install the front seat side airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps to connect the wire harness.



    B257725E02
  1. Engage the 5 clamps to connect the wire harness.



15. INSTALL FRONT SEATBACK HEATER


    B131243E01
  1. Using a tacker, install the seatback heater to the seatback cover at the position shown in the illustration with 6 new tack pins.

    NOTICE:
    Do not substitute other metal parts for tack pins.



16. INSTALL FRONT SEATBACK COVER

NOTICE:

  1. B131242E01
  2. Be careful not to damage the cover.
  3. When installing the hog rings, avoid wrinkling the cover.

  1. Using hog ring pliers, install the seatback cover to the seatback pad with 11 new hog rings.

  1. Install the seatback cover (with pad) to the front seat frame assembly (w/ adjuster).



    B131236
  1. w/ Front Seat Side Airbag:
    Fully cover the airbag with the 2 seatback cover brackets and install the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.



    B060977E01
  1. Attach the 4 claws to install the 2 headrest supports.



    B131240E01
  1. Attach the hooks.

  1. Using hog ring pliers, install 5 new hog rings.



17. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    B131246
  1. Push the seatback board in the direction indicated by the arrow in the illustration to attach the 2 claws.



    B131245
  1. Open the lower part of the seatback board. Then install the seatback board with the 2 screws.



18. INSTALL FRONT SEAT CUSHION HEATER


    B134550E01
  1. Using a tacker, install the seat cushion heater to the seat cushion cover at the position shown in the illustration with 10 new tack pins.

    NOTICE:
    Do not substitute other metal parts for tack pins.



19. INSTALL FRONT SEAT CUSHION COVER


    B131233E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 15 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the seat cushion cover (with pad) to the front seat frame assembly (w/ adjuster).



    B131230E01
  1. Attach the hooks and install the 2 clips.

  1. w/ Seat Heater System:
    Connect the 2 connectors.



20. INSTALL FRONT POWER SEAT SWITCH
  1. Connect the connector.



    B131280
  1. Install the switch with the 3 screws.



21. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


B133641E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding part of the seat adjuster.

  1. for Driver Seat:
    Attach the 2 clamps and connect the 2 connectors.

  1. for Passenger Seat:
    Attach the 2 clamps and connect the 2 connectors.



22. INSTALL FRONT SEAT CUSHION INNER SHIELD LH


    B131278
  1. Attach the clip and 3 claws to install the inner shield.

  1. Install the screw.



23. INSTALL FRONT POWER SEAT LUMBAR SWITCH


    B131279
  1. Install the switch to the cushion shield with the 2 screws.



24. INSTALL FRONT SEAT CUSHION SHIELD LH


    B131276
  1. Install the front No. 1 seat cushion inner shield to the cushion shield.

    1. Attach the claw to install the front No. 1 seat cushion inner shield.

    2. Install the screw.

  1. Connect the connector to the front power seat lumbar switch.



    B131275
  1. Attach the 3 claws and install the cushion shield (with front No. 1 seat cushion inner shield) to the front seat frame assembly (w/ adjuster).

  1. Install the 5 screws.



    B210579
  1. Connect the rubber band of the front seatback board to the front seat frame assembly (w/ adjuster).



25. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


26. INSTALL RECLINING POWER SEAT SWITCH KNOB