Home › BODY › SEAT › POWER SEAT SWITCH

POWER SEAT SWITCH > INSPECTION

for Preparation Click here



1. INSPECT FRONT POWER SEAT SWITCH (for LHD)


    B105970E06
  1. Measure the resistance between the terminals when each switch is operated.

    Standard resistance:
    Slide switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 9 (SLDF)
    FRONT
    Below 1 Ω
    4 (E) - 6 (SLDR)
    FRONT
    Below 1 Ω
    4 (E) - 6 (SLDR)
    OFF
    Below 1 Ω
    4 (E) - 9 (SLDF)
    OFF
    Below 1 Ω
    1 (B) - 6 (SLDR)
    REAR
    Below 1 Ω
    4 (E) - 9 (SLDF)
    REAR
    Below 1 Ω

    Front vertical switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 10 (FUP)
    UP
    Below 1 Ω
    4 (E) - 5 (FDWN)
    UP
    Below 1 Ω
    4 (E) - 5 (FDWN)
    OFF
    Below 1 Ω
    4 (E) - 10 (FUP)
    OFF
    Below 1 Ω
    1 (B) - 5 (FDWN)
    DOWN
    Below 1 Ω
    4 (E) - 10 (FUP)
    DOWN
    Below 1 Ω

    Lifter switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 7 (RUP)
    UP
    Below 1 Ω
    4 (E) - 8 (RDWN)
    UP
    Below 1 Ω
    4 (E) - 7 (RUP)
    OFF
    Below 1 Ω
    4 (E) - 8 (RDWN)
    OFF
    Below 1 Ω
    1 (B) - 8 (RDWN)
    DOWN
    Below 1 Ω
    4 (E) - 7 (RUP)
    DOWN
    Below 1 Ω

    Reclining switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 3 (RCLF)
    FRONT
    Below 1 Ω
    2 (RCLR) - 4 (E)
    FRONT
    Below 1 Ω
    2 (RCLR) - 4 (E)
    OFF
    Below 1 Ω
    3 (RCLF) - 4 (E)
    OFF
    Below 1 Ω
    1 (B) - 2 (RCLR)
    REAR
    Below 1 Ω
    3 (RCLF) - 4 (E)
    REAR
    Below 1 Ω

    If the result is not as specified, replace the switch.



2. REMOVE FRONT POWER SEAT SWITCH (for RHD)


    B105969E05
  1. Measure the resistance between the terminals when each switch is operated.

    Standard resistance:
    Slide switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 9 (SLDF)
    FRONT
    Below 1 Ω
    4 (E) - 6 (SLDR)
    FRONT
    Below 1 Ω
    4 (E) - 6 (SLDR)
    OFF
    Below 1 Ω
    4 (E) - 9 (SLDF)
    OFF
    Below 1 Ω
    1 (B) - 6 (SLDR)
    REAR
    Below 1 Ω
    4 (E) - 9 (SLDF)
    REAR
    Below 1 Ω

    Front vertical switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 5 (FUP)
    UP
    Below 1 Ω
    4 (E) - 10 (FDWN)
    UP
    Below 1 Ω
    4 (E) - 5 (FUP)
    OFF
    Below 1 Ω
    4 (E) - 10 (FDWN)
    OFF
    Below 1 Ω
    1 (B) - 10 (FDWN)
    DOWN
    Below 1 Ω
    4 (E) - 5 (FUP)
    DOWN
    Below 1 Ω

    Lifter switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 8 (RUP)
    UP
    Below 1 Ω
    4 (E) - 7 (RDWN)
    UP
    Below 1 Ω
    4 (E) - 8 (RUP)
    OFF
    Below 1 Ω
    4 (E) - 7 (RDWN)
    OFF
    Below 1 Ω
    1 (B) - 7 (RDWN)
    DOWN
    Below 1 Ω
    4 (E) - 8 (RUP)
    DOWN
    Below 1 Ω

    Reclining switch 
    Tester Connection
    Switch Condition
    Specified Condition
    1 (B) - 3 (RCLF)
    FRONT
    Below 1 Ω
    2 (RCLR) - 4 (E)
    FRONT
    Below 1 Ω
    2 (RCLR) - 4 (E)
    OFF
    Below 1 Ω
    3 (RCLF) - 4 (E)
    OFF
    Below 1 Ω
    1 (B) - 2 (RCLR)
    REAR
    Below 1 Ω
    3 (RCLF) - 4 (E)
    REAR
    Below 1 Ω

    If the result is not as specified, replace the switch.