DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | When one of following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic)
1. Either of the following is met (a) NSW (STAR) input signal is ON (b) P input signal is ON (c) N input signal is ON (d) R input signal is ON 2. Either of the following is met (a) 3 input signal is ON (b) L input signal is ON |
|

| Item | Measurement Item/ Range (Display) | Normal Condition | Diagnostic Note |
| Neutral Position Switch Signal | PNP switch status/ ON or OFF | Shift lever is: On P or N: ON Not on P or N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (R range) | PNP switch status/ ON or OFF | Shift lever is: On R: ON Not on R: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (P range) | PNP switch status/ ON or OFF | Shift lever is: On P: ON Not on P: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (N range) | PNP switch status/ ON or OFF | Shift lever is: On N: ON Not on N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (D range) | PNP switch status/ ON or OFF | Shift lever is: On D: ON Not on D: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (3 range) | PNP switch status/ ON or OFF | Shift lever is: On 3: ON Not on 3: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (2 range) | PNP switch status/ ON or OFF | Shift lever is: On 2: ON Not on 2: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| Shift switch status (L range) | PNP switch status/ ON or OFF | Shift lever is: On L: ON Not on L: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect |
| 1.CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - BATTERY) |
![]() |
Disconnect the B28 park/neutral position switch connector.
Turn the ignition switch on (IG).
Measure the voltage.
| Tester Connection | Specified Condition |
| 2 (RB) - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 2.CHECK WIRE HARNESS (OUTPUT SIGNAL) |
![]() |
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 4 (B) - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| 6 (PL) - 2 (RB) | P | Below 1 Ω |
| 6 (PL) - 2 (RB) | Not on P | 10 kΩ or higher |
| 4 (B) - 5 (L) | P or N | Below 1 Ω |
| 4 (B) - 5 (L) | Not on P or N | 10 kΩ or higher |
| 1 (RL) - 2 (RB) | R | Below 1 Ω |
| 1 (RL) - 2 (RB) | Not on R | 10 kΩ or higher |
| 9 (NL) - 2 (RB) | N | Below 1 Ω |
| 9 (NL) - 2 (RB) | Not on N | 10 kΩ or higher |
| 7 (DL) - 2 (RB) | D | Below 1 Ω |
| 7 (DL) - 2 (RB) | Not on D | 10 kΩ or higher |
| 3 (2L) - 2 (RB) | 2 | Below 1 Ω |
| 3 (2L) - 2 (RB) | Not on 2 | 10 kΩ or higher |
| 8 (LL) - 2 (RB) | L | Below 1 Ω |
| 8 (LL) - 2 (RB) | Not on L | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (ECM - PARK/NEUTRAL POSITION SWITCH) |
Connect park/neutral position switch.
![]() |
Disconnect the B32 ECM connector.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Shift Lever Position | Specified Condition |
| B32-73 (P) - Body ground | P | 10 to 14 V |
| B32-73 (P) - Body ground | Not on P | Below 1 V |
| B32-53 (R) - Body ground | R | 10 to 14 V* |
| B32-53 (R) - Body ground | Not on R | Below 1 V |
| B32-54 (N) - Body ground | N | 10 to 14 V |
| B32-54 (N) - Body ground | Not on N | Below 1 V |
| B32-56 (D) - Body ground | D or 3 | 10 to 14 V |
| B32-56 (D) - Body ground | Not on D or 3 | Below 1 V |
| B32-55 (2) - Body ground | 2 | 10 to 14 V |
| B32-55 (2) - Body ground | Not on 2 | Below 1 V |
| B32-74 (L) - Body ground | L | 10 to 14 V |
| B32-74 (L) - Body ground | Not on L | Below 1 V |
|
| ||||
| OK | |
| 5.CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH) |
![]() |
Disconnect the E45 switch connector.
Turn the ignition switch on (IG).
Measure the voltage when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| 1 (NSSD) - Body ground | D and 3 | 10 to 14 V |
| 1 (NSSD) - Body ground | Not on D and 3 | Below 1 V |
|
| ||||
| OK | |
| 6.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Measure the resistance of the switch when the shift lever is moved to each position.
| Tester Connection | Shift Lever Position | Specified Condition |
| 1 (NSSD) - 2 (AT3) | D | 10 kΩ or higher |
| 1 (NSSD) - 2 (AT3) | 3 | Below 1 Ω |
|
| ||||
| OK | |
| 7.CHECK WIRE HARNESS (TRANSMISSION CONTROL SWITCH - ECM) |
Connect E45 switch connector.
![]() |
Disconnect the A12 ECM connector.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Shift Lever Position | Specified Condition |
| A12-26 (3) - Body ground | 3 | 10 to 14 V |
| A12-26 (3) - Body ground | Not on 3 | Below 1 V |
|
| ||||
| OK | ||
| ||
| 8.CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the B32 ECM connector.
Disconnect the B28 park/neutral position switch connector.
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| B28-4 (B) - B32-52 (STAR) | Below 1 Ω |
| Tester Connection | Specified Condition |
| B28-4 (B) or B32-52 (STAR) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||