DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
DTC P0430 Catalyst System Efficiency Below Threshold (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | OSC value is smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|
| P0430 | OSC value is smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|

| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC output) | Proceed to |
| P0420 and/or P0430 | A |
| P0420 and/or P0430 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (A/F CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at a engine speed of 2500 rpm for approximately 90 seconds.
On the tester, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume.)
Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1 S1 or AFS B2 S1 (A/F) | +25 % | Rich | Less than 3.0 V |
| AFS B1 S1 or AFS B2 S1 (A/F) | -12.5 % | Lean | More than 3.35 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | +25 % | Rich | More than 0.55 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | -12.5 % | Lean | Less than 0.4 V |
| Status AFS B1 S1 or AFS B2 S1 | Status O2S B1 S2 or O2S B2 S2 | A/F Condition and A/F and HO2 Sensor Condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean/Lean | Lean/Rich | A/F sensor malfunction | - |
| B |
| Rich/Rich | Lean/Rich | A/F sensor malfunction | May occur |
| B |
| Lean/Rich | Lean/Lean | HO2 sensor malfunction | - |
| C |
| Lean/Rich | Rich/Rich | HO2 sensor malfunction | - |
| C |
| Lean/Lean | Lean/Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich/Rich | Rich/Rich | Actual air-fuel ratio lean | - |
| A |
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
|
| ||||
| OK | ||
| ||