DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 | Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic) |
|
| P0032 | Air-Fuel Ratio (A/F) sensor heater current more than 10 A (1 trip detection logic) |
|
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the B7 A/F sensor connector.
Measure the resistance of the A/F sensor connector.
| Tester Connection | Specified Condition |
| HA1A (1) - +B (2) | 1.8 Ω to 3.4 Ω at 20°C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR) |
![]() |
Disconnect the B7 A/F sensor connector.
Turn the ignition switch on (IG).
Measure the voltage between the terminals of the B7 A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (B7-2) - Body ground | 9 to 14 V |
Reconnect the A/F sensor connector.
|
| ||||
| NG | |
| 3.INSPECT INTEGRATION RELAY (EFI MAIN RELAY) |
Remove the integration relay from the engine room relay block.
Inspect the EFI MAIN fuse.
![]() |
Remove the EFI MAIN fuse from the integration relay.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
Inspect the EFI MAIN relay.
Measure the EFI MAIN relay resistance.
| Tester Connection | Specified Condition |
| 1C-1 - 1A-4 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1A-2 and 1A-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (A/F SENSOR - INTEGRATION RELAY) |
![]() |
Disconnect the B7 A/F sensor connector.
Remove the integration relay from the engine room No. 1 relay block (R/B).
Measure the resistance.
| Tester Connection | Specified Condition |
| +B (B7-2) - Engine room No. 1 R/B (1A-4) | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (B7-2) or Engine room Engine room No. 1 R/B (1A-4) - Body ground | 10 kΩ or higher |
Reconnect the A/F sensor connector.
Reinstall the integration relay.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the B7 A/F sensor connector.
Disconnect the B32 ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| HA1A (B7-1) - HA1A (B32-109) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (B7-1) or HA1A (B32-109) - Body ground | 10 kΩ or higher |
Reconnect the A/F sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 1 minute or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0031 or P0032 | B |
|
| ||||
| A | ||
| ||