DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
DTC P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 P2A03 | Calculated value for air-fuel ratio (A/F) sensor response rate deterioration level is less than threshold |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1 S1 or AFS B2 S1 (A/F) | +25 % | Rich | Less than 3.0 V |
| AFS B1 S1 or AFS B2 S1 (A/F) | -12.5 % | Lean | More than 3.35 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | +25 % | Rich | More than 0.55 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | -12.5 % | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| P2A00 and/or P2A03 and other DTCs | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| HA1A (B7-1) - HA1A (B96-86) | Below 1 Ω |
| A1A+ (B7-3) - A1A+ (B96-93) | Below 1 Ω |
| A1A- (B7-4) - A1A- (B96-116) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA2A (B67-1) - HA2A (B96-109) | Below 1 Ω |
| A2A+ (B67-3) - A2A+ (B96-120) | Below 1 Ω |
| A2A- (B67-4) - A2A- (B96-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (B7-1) or HA1A (B96-86) - Body ground | 10 kΩ or higher |
| A1A+ (B7-3) or A1A+ (B96-93) - Body ground | 10 kΩ or higher |
| A1A- (B7-4) or A1A- (B96-116) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA2A (B67-1) or HA2A (B96-109) - Body ground | 10 kΩ or higher |
| A2A+ (B67-3) or A2A+ (B96-120) - Body ground | 10 kΩ or higher |
| A2A- (B67-4) or A2A- (B96-119) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 3.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| No output | B |
|
| ||||
| A | |
| 5.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 6.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2A00 and/or P2A03 | B |
|
| ||||
| A | ||
| ||