DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 | Conditions (a) and (b) continue for 10 seconds or more (2 trip detection logic): (a) A/F sensor voltage more than 3.8 V (b) Heated Oxygen (HO2) sensor voltage 0.15 V or more |
|
| While fuel-cut operation performed (during vehicle deceleration), A/F sensor current 3.6 mA or more for 3 seconds (2 trip detection logic) |
| |
| P2196 | Conditions (a) and (b) continue for 10 seconds or more (2 trip detection logic): (a) A/F sensor voltage less than 2.8 V for 10 seconds (b) HO2 sensor voltage less than 0.6 V |
|
| While fuel-cut operation performed (during vehicle deceleration), A/F sensor current less than 1.0 mA for 3 seconds (2 trip detection logic) |
|




| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1 S1 (A/F) | +25% | Rich | Less than 3.0 |
| -12.5% | Lean | More than 3.35 | |
| O2S B1 S2 (HO2) | +25% | Rich | More than 0.5 |
| -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester ON.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P2195 or P2196 | A |
| P2195 or P2196 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Clear DTCs (Click here).
Drive the vehicle in accordance with the drive pattern described in the CONFIRMATION DRIVING PATTERN.
Select the following menu items: Powertrain / Engine and ECT / Data List / Monitor Status.
Check that the status of O2S(A/FS) Monitor is Complete.
If the status is still Incomplete, drive the vehicle according to the driving pattern again.
Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / AFS B1 S1.
Check the test value of the A/F sensor output current during fuel-cut (Refer to the Monitor Driving Pattern 2 [Detail for (h) through (k)] in the CONFIRMATION DRIVING PATTERN).
| Test Value | Proceed to |
| Within normal range (1.0 mA or more, and less than 3.6 mA) | A |
| Outside normal range (Less than 1.0 mA, or 3.6 mA or more) | B |
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester ON.
Warm up the A/F sensor at an engine speed of 2,500 rpm for 90 seconds.
On the tester, select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / Snapshot / AFS B1 S1 and Engine Speed.
Check the A/F sensor voltage 3 times, when the engine is in each of the following conditions:
| Condition | A/F Sensor Voltage Variation | Reference |
| (1) and (2) | Remains at approximately 3.3 V | Between 3.1 V and 3.5 V |
| (3) | Increases to 3.8 V or more | This occurs during engine deceleration (when fuel-cut performed) |

|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Read DTCs using the intelligent tester.
Select the following menu items: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| P2195 or P2196 | A |
| No output | B |
|
| ||||
| A | |
| 6.REPLACE AIR-FUEL RATIO SENSOR |
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Read DTCs using the intelligent tester.
Select the following menu items: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2195 or P2196 | B |
|
| ||||
| A | ||
| ||
| 9.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the B7 A/F sensor connector.
Measure the resistance of the A/F sensor connector.
| Tester Connection | Specified Condition |
| HA1A (1) - +B (2) | 1.8 Ω to 3.4 Ω at 20°C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 10.INSPECT INTEGRATION RELAY (EFI MAIN RELAY) |
Remove the integration relay from the engine room relay block.
Inspect the EFI MAIN fuse.
![]() |
Remove the EFI MAIN fuse from the integration relay.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
Inspect the EFI MAIN relay.
Measure the EFI MAIN relay resistance.
| Tester Connection | Specified Condition |
| 1C-1 - 1A-4 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1A-2 and 1A-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the B7 A/F sensor connector.
Turn the ignition switch on (IG).
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (B7-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the B32 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| HA1A (B7-1) - HA1A (B32-109) | Below 1 Ω |
| A1A+ (B7-3) - A1A+ (B32-112) | Below 1 Ω |
| A1A- (B7-4) - A1A- (B32-113) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HA1A (B7-1) or HA1A (B32-109) - Body ground | 10 kΩ or higher |
| A1A+ (B7-3) or A1A+ (B32-112) - Body ground | 10 kΩ or higher |
| A1A- (B7-4) or A1A- (B32-113) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 12.REPLACE AIR-FUEL RATIO SENSOR |
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Read DTCs using the intelligent tester.
Select the following menu items: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2195 or P2196 | B |
|
| ||||
| A | ||
| ||