DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 | Conditions (a) and (b) are met for 10 seconds or more (2 trip detection logic): (a) The air fuel ratio sensor voltage is higher than 3.8 V. (b) The heated oxygen sensor voltage is 0.21 V or higher. |
|
| While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 3.6 mA or higher (2 trip detection logic). |
| |
| P2196 | Conditions (a) and (b) are met for 10 seconds or more (2 trip detection logic): (a) The air fuel ratio sensor voltage is below 2.8 V for 10 seconds. (b) The heated oxygen sensor voltage is below 0.6 V. |
|
| While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is below 0.78 mA (2 trip detection logic). |
|



| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio sensor) | +25% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen sensor) | +25% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Case | Air Fuel Ratio Sensor Output Voltage | Heated Oxygen Sensor Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P2195 or P2196 is output | A |
| "P2195 or P2196" and "P0136, P0137 or P0138" are output | A |
| P2195 or P2196 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF AIR FUEL RATIO SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / Monitor Status.
Check that the status of "O2 Sensor" is "Complete".
If the status is still "Incomplete", drive the vehicle according to the driving pattern again.
Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1S1.
Check the test value of the air fuel ratio sensor output current during fuel-cut (refer to Monitor Driving Pattern 2 [Detail for "C" through "F"] in Confirmation Driving Pattern).
| Test Value | Proceed to |
| Within normal range (0.78 mA or higher, and below 3.6 mA) | A |
| Outside normal range (Below 0.78 mA, or 3.6 mA or higher) | B |
|
| ||||
| A | |
| 3.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Voltage B1S1 and Engine Speed / Function / Snap Shot Record.
Check the air fuel ratio sensor voltage 3 times, once under each of the following conditions:
Engine idling (for at least 30 seconds) (Step "A").
Engine running at an engine speed of approximately 2500 rpm (without any sudden changes in engine speed) (Step "B").
Engine speed to raised 4000 rpm and then accelerator pedal quickly released so that throttle valve is fully closed (Step "C").
| Condition | A/F Sensor Voltage Variation | Reference |
| Step "A" and Step "B" | Remains at approximately 3.3 V | Between 3.1 V and 3.5 V |
| Step "C" | Increases to 3.8 V or higher | Occurs during engine deceleration (when fuel-cut performed) |

|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 6.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||
| 9.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | ||
| ||
| 10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor .
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B7-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B7-1 (HA1A) - B32-109 (HA1A) | Always | Below 1 Ω |
| B7-3 (A1A+) - B32-112 (A1A+) | Always | Below 1 Ω |
| B7-4 (A1A-) - B32-113 (A1A-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B7-1 (HA1A) or B32-109 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B7-3 (A1A+) or B32-112 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B7-4 (A1A-) or B32-113 (A1A-) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the air fuel ratio sensor connector.

|
| ||||
| OK | |
| 12.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage.
|
| ||||
| OK | |
| 13.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 14.INSPECT FUEL INJECTOR ASSEMBLY |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .
|
| ||||
| OK | |
| 15.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the intelligent tester on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2195, P2196, P2197 or P2198 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | ||
| ||