DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |
DTC P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1) |
DTC P2198 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 P2197 | Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) Air-Fuel Ratio (A/F) sensor voltage is more than 3.8 V (b) Heated Oxygen (HO2) sensor voltage is 0.15 V or more |
|
| P2195 P2197 | While fuel-cut operation is performed (during vehicle deceleration), air-fuel ratio (A/F) sensor current is 3.6 mA or more for 3 seconds (2 trip detection logic) |
|
| P2196 P2198 | Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) A/F sensor voltage is less than 2.8 V (b) HO2 sensor voltage is less than 0.85 V |
|
| P2196 P2198 | While fuel-cut operation is performed (during vehicle deceleration), air-fuel ratio (A/F) sensor current is 1.4 mA for 3 seconds (2 trip detection logic) |
|



| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +25 % | Rich | Less than 3.0 V |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5 % | Lean | More than 3.35 V |
| O2S B1S2 or O2S B2S2 (HO2) | +25 % | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5 % | Lean | Less than 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, 2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2195, P2196, P2197, or P2198 | A |
| P2195, P2196, P2197, or P2198 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the Air-Fuel Ratio (A/F) sensor at an engine speed of 2500 rpm for 90 seconds.
On the tester, enter the following menus: Powertrain / Engine and ECT / Data List / AFS B1 S1 or AFS B2 S1 and Engine Speed.
Check the A/F sensor voltage three times, when the engine is in each of the following conditions:
While idling (check for at least 30 seconds)
At an engine speed of approximately 2500 rpm (without any sudden changes in engine speed)
Raise the engine speed to 4000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed.
| Condition | A/F Sensor Voltage Variation | Reference |
| (1) and (2) | Changes at approximately 3.3 V | Between 3.1 V and 3.5 V |
| (3) | Increases to 3.8 V or more | This occurs during engine deceleration (when fuel-cut performed) |

|
| ||||
| NG | |
| 3.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HA1A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA1A (1) - A1A- (4) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HA2A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA2A (1) - A2A- (4) | Always | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| HA1A (B7-1) - HA1A (B96-86) | Below 1 Ω |
| A1A+ (B7-3) - A1A+ (B96-93) | Below 1 Ω |
| A1A- (B7-4) - A1A- (B96-116) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA2A (B67-1) - HA2A (B96-109) | Below 1 Ω |
| A2A+ (B67-3) - A2A+ (B96-120) | Below 1 Ω |
| A2A- (B67-4) - A2A- (B96-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (B7-1) or HA1A (B96-86) - Body ground | 10 kΩ or higher |
| A1A+ (B7-3) or A1A+ (B96-93) - Body ground | 10 kΩ or higher |
| A1A- (B7-4) or A1A- (B96-116) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA2A (B67-1) or HA2A (B96-109) - Body ground | 10 kΩ or higher |
| A2A+ (B67-3) or A2A+ (B96-120) - Body ground | 10 kΩ or higher |
| A2A- (B67-4) or A2A- (B96-119) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 5.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 6.CHECK FUEL PRESSURE (HIGH PRESSURE SIDE AND LOW PRESSURE SIDE) |
Check the fuel pressure (Click here).
|
| ||||
| OK | |
| 7.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 8.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| P2195, P2196, P2197, or P2198 | A |
| No output | B |
|
| ||||
| A | |
| 10.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | ||
| ||
| 11.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| P2195, P2196, P2197, or P2198 | A |
| No output | B |
|
| ||||
| A | |
| 13.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 14.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2195, P2196, P2197 or P2198 | B |
|
| ||||
| A | ||
| ||