ENGINE UNIT > INSPECTION |
| 1. INSPECT VALVE LASH ADJUSTER ASSEMBLY |
![]() |
Place the lash adjuster into a container full of engine oil.
Insert the SST's tip into the lash adjuster's plunger and use the tip to press down on the check ball inside the plunger.
Squeeze the SST and lash adjuster together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with a finger.
| 2. INSPECT CAMSHAFT |
Inspect the camshaft for runout.
![]() |
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Using a micrometer, measure the cam lobe height.
| Item | Specified Condition |
| Intake | 44.316 to 44.416 mm (1.7447 to 1.7487 in.) |
| Exhaust | 44.262 to 44.362 mm (1.7426 to 1.7465 in.) |
| Item | Specified Condition |
| Intake | 44.166 mm (1.7388 in.) |
| Exhaust | 44.112 mm (1.7367 in.) |
![]() |
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
| No. 1 journal | 35.946 to 35.960 mm (1.4152 to 1.4157 in.) |
| Other journals | 25.959 to 25.975 mm (1.0220 to 1.0226 in.) |
| 3. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Clamp the camshaft in a vise.
![]() |
Put the camshaft timing gear and camshaft together by aligning the key groove and straight pin.
Lightly press the gear against the camshaft, and turn the gear. Push further at the position where the pin enters the groove.
Check that there is no clearance between the gear's fringe and the camshaft.
![]() |
Tighten the flange bolt with the camshaft timing gear secured in place.
Check the lock of the camshaft timing gear.
Clamp the camshaft in a vise, and confirm that the camshaft timing gear is locked.
Release the lock pin.
![]() |
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path on the opposite side to that of the advance side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the two opened paths.
![]() |
Check that the camshaft timing gear revolves in the advance direction when reducing the air pressure applied to the retard side path.
When the camshaft timing gear reaches the most advanced position, release the air pressure first from the retard side path and advance side path, in that order.
Check for smooth rotation.
Turn the camshaft timing gear within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear is locked at the most retarded position.
![]() |
Remove the flange bolt and camshaft timing gear.
| 4. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Clamp the camshaft in a vise.
![]() |
Put the camshaft timing exhaust gear and camshaft together by aligning the key groove and straight pin.
Lightly press the gear against the camshaft, and turn the gear. Push further at the position where the pin enters the groove.
Check that there is no clearance between the gear's fringe and the camshaft.
![]() |
Tighten the flange bolt with the camshaft timing exhaust gear fixed in place.
Check the camshaft timing exhaust gear lock.
Make sure that the camshaft timing exhaust gear is locked.
Release the lock pin.
![]() |
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path on the opposite side to that of the advance side path, as shown in the illustration.
![]() |
Apply approximately 200 kPa (2.0 kgf/cm2, 28 psi) of air pressure to the two opened paths.
![]() |
Make sure that the camshaft timing exhaust gear turns in the retard direction when reducing the air pressure applied to the advance side path.
When the camshaft timing exhaust gear moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.
Check for smooth rotation.
Turn the camshaft timing exhaust gear within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear turns smoothly.
Check the lock at the most advanced position.
Make sure that the camshaft timing exhaust gear is locked at the most advanced position.
![]() |
Remove the flange bolt and camshaft timing exhaust gear.
| 5. INSPECT CYLINDER HEAD SET BOLT |
![]() |
Using a vernier caliper, measure the minimum diameter of the elongated thread at the measuring point.
| 6. INSPECT CHAIN SUB-ASSEMBLY |
![]() |
Using a spring scale, pull the chain with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 16 links.
| 7. INSPECT NO. 2 CHAIN SUB-ASSEMBLY |
![]() |
Pull the chain with a force of 147 N (15 kgf, 33 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 16 links.
| 8. INSPECT CRANKSHAFT TIMING GEAR OR SPROCKET |
![]() |
Place the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
| 9. INSPECT IDLE SPROCKET ASSEMBLY |
![]() |
Place the chain around the sprocket.
Using a vernier caliper, measure the sprocket diameter with the chain.
| 10. INSPECT IDLE GEAR SHAFT OIL CLEARANCE |
![]() |
Using a micrometer, measure the idle gear shaft diameter.
![]() |
Using a caliper gauge, measure the inside diameter of the idle gear.
Subtract the idle gear shaft diameter measurement from the idle gear inside diameter measurement.
| 11. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
If necessary, replace the chain tensioner.
| 12. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
| 13. INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Check that the plunger moves smoothly.
Measure the worn depth of the chain tensioner.
| 14. INSPECT CHAIN TENSIONER SLIPPER |
![]() |
Measure the worn depth of the chain tensioner slipper.
| 15. INSPECT NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Measure the worn depth of the chain vibration damper.
| 16. INSPECT NO. 2 CHAIN VIBRATION DAMPER |
![]() |
Measure the worn depth of the chain vibration damper.
| 17. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder block and manifolds.
| Item | Specified Condition |
| Cylinder head lower side | 0.05 mm (0.0020 in.) |
| Intake side | 0.08 mm (0.0031 in.) |
| Exhaust side | 0.08 mm (0.0031 in.) |
![]() |
Using a dye penetrate, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.
| 18. INSPECT INTAKE VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
![]() |
Using a vernier caliper, measure the valve's overall length.
| 19. INSPECT EXHAUST VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
![]() |
Using a vernier caliper, measure the valve's overall length.
| 20. INSPECT INTAKE VALVE SEAT |
![]() |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat by using the following procedure.
If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts in the middle of the valve face with the width between 1.1 and 1.5 mm (0.043 and 0.059 in.).
| 21. INSPECT EXHAUST VALVE SEAT |
![]() |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat by using the following procedure.
If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts in the middle of the valve face with the width between 1.2 and 1.6 mm (0.047 and 0.063 in.).
| 22. INSPECT INNER COMPRESSION SPRING |
![]() |
Using a vernier caliper, measure the free length of the inner compression spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| 23. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Specified Condition |
| Intake | 0.025 to 0.060 mm (0.0010 to 0.0024 in.) |
| Exhaust | 0.030 to 0.065 mm (0.0012 to 0.0026 in.) |
| Item | Specified Condition |
| Intake | 0.08 mm (0.0031 in.) |
| Exhaust | 0.10 mm (0.0039 in.) |
| 24. INSPECT CAMSHAFT THRUST CLEARANCE |
Inspect the bank 1 camshafts.
![]() |
Install the bank 1 camshafts.
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
Inspect the bank 2 camshafts.
Install the bank 2 camshafts.
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 25. INSPECT CAMSHAFT OIL CLEARANCE |
![]() |
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps.
Remove the bearing caps.
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| No. 1 journal | 0.040 to 0.079 mm (0.0016 to 0.0031 in.) |
| Other journals | 0.025 to 0.062 mm (0.0010 to 0.0024 in.) |
| Item | Specified Condition |
| No. 1 journal | 0.10 mm (0.0039 in.) |
| Other journals | 0.09 mm (0.0035 in.) |
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps.
Remove the bearing caps.
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| No. 1 journal | 0.040 to 0.079 mm (0.0016 to 0.0031 in.) |
| Other journals | 0.025 to 0.062 mm (0.0010 to 0.0024 in.) |
| Item | Specified Condition |
| No. 1 journal | 0.10 mm (0.0039 in.) |
| Other journals | 0.09 mm (0.0035 in.) |
| 26. INSPECT CYLINDER BLOCK FOR WARPAGE |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surface of the cylinder head gasket.
![]() |
Visually check the cylinder for vertical scratches.
If deep scratches are present, rebore all 6 cylinders. If necessary, replace the cylinder block.
| 27. INSPECT CYLINDER BORE |
![]() |
Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.
| 28. INSPECT PISTON SUB-ASSEMBLY WITH PIN |
![]() |
Using a micrometer, measure the piston diameter at right angles to the piston center line where the distance from the bottom edge of the piston is as specified.
| 29. INSPECT PISTON OIL CLEARANCE |
Measure the cylinder bore diameter in the thrust direction.
Subtract the piston diameter measurement from the cylinder bore diameter measurement.
| 30. INSPECT RING GROOVE CLEARANCE |
![]() |
Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.
| Item | Specified Condition |
| No. 1 | 0.020 to 0.070 mm (0.0008 to 0.0028 in.) |
| No. 2 | 0.020 to 0.060 mm (0.0008 to 0.0024 in.) |
| Oil | 0.070 to 0.150 mm (0.0028 to 0.0059 in.) |
| 31. INSPECT PISTON RING END GAP |
![]() |
Insert the piston ring into the cylinder bore.
Using a piston, push the piston ring a little beyond the bottom of the ring travel, 110 mm (4.33 in.) from the top of the cylinder block.
![]() |
Using a feeler gauge, measure the end gap.
| Item | Specified Condition |
| No. 1 | 0.25 to 0.35 mm (0.0098 to 0.0138 in.) |
| No. 2 | 0.50 to 0.60 mm (0.0197 to 0.0236 in.) |
| Oil | 0.10 to 0.40 mm (0.0039 to 0.0157 in.) |
| Item | Specified Condition |
| No. 1 | 0.50 mm (0.0197 in.) |
| No. 2 | 0.85 mm (0.0335 in.) |
| Oil | 0.60 mm (0.0236 in.) |
| 32. INSPECT PISTON PIN OIL CLEARANCE |
![]() |
Check each mark on the piston, piston pin and connecting rod.
![]() |
Using a caliper gauge, measure the inside diameter of the piston pin hole.
| Mark | Specified Condition |
| A | 22.001 to 22.004 mm (0.8662 to 0.8663 in.) |
| B | 22.005 to 22.007 mm (0.8663 to 0.8664 in.) |
| C | 22.008 to 22.010 mm (0.8665 to 0.8665 in.) |
![]() |
Using a micrometer, measure the piston pin diameter.
| Mark | Specified Condition |
| A | 21.997 to 22.000 mm (0.8660 to 0.8661 in.) |
| B | 22.001 to 22.003 mm (0.8662 to 0.8663 in.) |
| C | 22.004 to 22.006 mm (0.8663 to 0.8664 in.) |
Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.
![]() |
Using a caliper gauge, measure the inside diameter of the connecting rod bush.
| Mark | Specified Condition |
| A | 22.005 to 22.008 mm (0.8663 to 0.8665 in.) |
| B | 22.009 to 22.011 mm (0.8665 to 0.8666 in.) |
| C | 22.012 to 22.014 mm (0.8666 to 0.8667 in.) |
Subtract the piston pin diameter measurement from the bush inside diameter measurement.
| 33. INSPECT CONNECTING ROD SUB-ASSEMBLY |
![]() |
Using a rod aligner and feeler gauge, check the connecting rod alignment.
Check for bend.
![]() |
Check for twist.
| 34. INSPECT CONNECTING ROD BOLT |
![]() |
Using a vernier caliper, measure the tension portion diameter of the bolt.
| 35. INSPECT CRANKSHAFT |
![]() |
Inspect for circle runout.
Place the crankshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
![]() |
Inspect the main journals.
Using a micrometer, measure the diameter of each main journal.
Check each main journal for taper and out-of-round as shown in the illustration.
![]() |
Inspect the crank pin.
Using a micrometer, measure the diameter of each crank pin.
Check each crank pin for taper and out-of-round as shown in the illustration.
| 36. INSPECT CRANKSHAFT BEARING CAP SET BOLT |
![]() |
Using a vernier caliper, measure the minimum diameter of the compressed thread at the measuring point.