Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

  1. When the engine is running or the ignition switch is on (IG) and the window lock switch of the power window regulator master switch is normal, the front passenger door power window regulator motor is driven by operating the front passenger door power window regulator switch.

WIRING DIAGRAM


B138211E03


INSPECTION PROCEDURE

1.CHECK WIRE HARNESS (INPUT POWER SUPPLY)
B107969E34
  1. Disconnect the G3*1 or H8*2 switch connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    G3-3 (B) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    H8-3 (B) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
INSPECT FUSE AND REPLACE IT IF NECESSARY, OR INSPECT AND REPAIR WIRE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
B116301E05
  1. Remove the power window regulator switch.

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (D) - 2 (SD)
    3 (B) - 4 (U)
    UP
    Below 1 Ω
    4 (U) - 5 (SU)
    1 (D) - 2 (SD)
    OFF
    Below 1 Ω
    1 (D) - 3 (B)
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
OK


3.CHECK WIRE HARNESS (REGULATOR SWITCH - REGULATOR MOTOR)

B111941E23

  1. Disconnect the G3*1 or H8*2 switch connector.

  1. Disconnect the G2*1 or H7* motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    G3-4 (U) - G2-2 (U)
    Below 1 Ω
    G3-1 (D) - G2-1 (D)
    Below 1 Ω
    G3-4 (U) or G2-2 (U) - Body ground
    10 kΩ or higher
    G3-1 (D) or G2-1 (D) - Body ground
    10 kΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    H8-4 (U) - H7-2 (U)
    Below 1 Ω
    H8-1 (D) - H7-1 (D)
    Below 1 Ω
    H8-4 (U) or H7-2 (U) - Body ground
    10 kΩ or higher
    H8-1 (D) or H7-1 (D) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)
B086400E01
B086401E01
  1. LHD:

    1. Remove the power window regulator motor.

    2. Apply the battery voltage to connector terminals 1 and 2.

      NOTICE:
      Do not apply the battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates counterclockwise

  1. RHD:

    1. Remove the power window regulator motor.

    2. Apply the battery voltage to connector terminal 1 and 2.

      NOTICE:
      Do not apply the battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates counterclockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side)
OK


5.CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR SWITCH)

E124649E07

  1. Disconnect the H2*1 or G8*2 switch connector.

  1. Disconnect the G3*1 or H8*2 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LHD:
    Tester Connection
    Specified Condition
    H2-16 (U) - G3-5 (SU)
    Below 1 Ω
    H2-15 (D) - G3-2 (SD)
    Below 1 Ω
    H2-16 (U) or G3-5 (SU) - Body ground
    10 kΩ or higher
    H2-15 (D) or G3-2 (SD) - Body ground
    10 kΩ or higher
    for RHD:
    Tester Connection
    Specified Condition
    G8-12 (U) - H8-5 (SU)
    Below 1 Ω
    G8-13 (D) - H8-2 (SD)
    Below 1 Ω
    G8-12 (U) or H8-5 (SU) - Body ground
    10 kΩ or higher
    G8-13 (D) or H8-2 (SD) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY