ENTRY AND START SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) |


Disconnect the ID, IE, E18 and E19 junction block connectors.
Measure the voltages and resistances of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| AM1 (E19-1) - Body ground | W - Body ground | +B power supply | Always | 11 to 14 V |
| AM2 (E18-6) - Body ground | W - Body ground | +B power supply | Always | 11 to 14 V |
| SSW1 (E19-10) - Body ground | W - Body ground | Engine switch signal | Engine switch pushed | Below 1 Ω |
| SSW1 (E19-10) - Body ground | W - Body ground | Engine switch signal | Engine switch not pushed | 10 kΩ or higher |
| SSW2 (E19-9) - Body ground | B - Body ground | Engine switch signal | Engine switch pushed | Below 1 Ω |
| SSW2 (E19-9) - Body ground | B - Body ground | Engine switch signal | Engine switch not pushed | 10 kΩ or higher |
| GND1 (IE-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| GND2 (E19-4) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| LIN1 (ID-9) - Body ground | V - Body ground | LIN line | Always | 10 kΩ or higher |
Reconnect the ID, IE, E18 and E19 junction block connectors.
Measure the voltages of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| ACCD (E18-4) - GND2 (E19-4) | R - W-B | ACC signal | Engine switch on (ACC) | 11 to 14 V |
| ACCD (E18-4) - GND2 (E19-4) | R - W-B | ACC signal | Engine switch off | Below 1 V |
| IG2D (E19-5) - GND2 (E19-4) | W - W-B | IG2 signal | Engine switch on (IG) | 11 to 14 V |
| IG2D (E19-5) - GND2 (E19-4) | W - W-B | IG2 signal | Engine switch on (ACC) | Below 1 V |
| SLR+ (E18-7) - GND2 (E19-4) | Y - W-B | Steering lock motor signal | Steering lock motor operating | Below 1 V |
| SLR+ (E18-7) - GND2 (E19-4) | Y - W-B | Steering lock motor signal | Steering lock motor does not operate | 11 to 14 V |
| SLP (E18-18) - GND2 (E19-4) | G - W-B | Steering lock actuator position signal | Steering lock locked | 11 to 14 V |
| SLP (E18-18) - GND2 (E19-4) | G - W-B | Steering lock actuator position signal | Steering lock released | Below 1 V |
| SPD (IC-8) - GND2 (E19-4) | V - W-B | Speed signal from combination meter | Engine switch on (IG), Rotate driving wheel slowly | Pulse generation (see waveform 1) |
| TACH (E20-2) - GND2 (E19-4) | GR - W-B | Tachometer signal | Engine running | Pulse generation (see waveform 2) |
| STSW (E20-4) - GND2 (E19-4) | R - W-B | Starter activation request signal | When all condition are met:
| 11 to 14 V* |
| STR (E20-3) - GND2 (E19-4) | W - W-B | Park / neutral position switch | When all condition are met:
| Below 1 V |
| STR2 (E20-14) - GND2 (E19-4) | W - W-B | Starter signal | When all condition are met:
| 11 to 14 V* |
| INDS (E20-1) - GND2 (E19-4) | R - W-B | Vehicle condition signal | When all condition are met:
| 11 to 14 V |
| INDW (E20-8) - GND2 (E19-4) | Y - W-B | Vehicle condition signal | When all condition are met:
| 11 to 14 V |
| SWIL (E19-8) - GND2 (E19-4) | G - W-B | Illumination signal | Light control switch TAIL or HEAD | 11 to 14 V |
| STP (E18-14) - GND2 (E19-4) | L - W-B | Stop light switch signal | Brake pedal depressed | 11 to 14 V |
![]() |
Using an oscilloscope, check waveform 1.
| Item | Content |
| Symbols (Terminal No.) | SPD (IC-8) - GND2 (E19-4) |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Driving at approx. 20 km/h (12 mph) |
![]() |
Using an oscilloscope, check waveform 2.
| Item | Content |
| Symbols (Terminal No.) | TACH (E20-2) - GND2 (E19-4) |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Engine idling |
| CHECK CERTIFICATION ECU |

Disconnect the E63 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| +B (E63-1) - Body ground | R - Body ground | +B power supply | Always | 11 to 14 V |
| IG (E63-18) - Body ground | B - Body ground | Ignition power supply | Engine switch on (IG) | 11 to 14 V |
| IG (E63-18) - Body ground | B - Body ground | Ignition power supply | Engine switch off | Below 1 V |
| LIN (E63-10) - Body ground | V - Body ground | LIN line | Always | 10 kΩ or higher |
| E (E63-17) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK ECM |

Disconnect the A12 and B32 ECM connectors.
Measure the voltages and resistances of the wire harness side connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| BATT (A12-20) - E1 (B32-104) | W - BR | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| +B (A12-2) - E1 (B32-104) | B - BR | Power source of ECM | Engine switch on (IG) | 11 to 14 V |
| +B2 (A12-1) - E1 (B32-104) | B - BR | Power source of ECM | Engine switch on (IG) | 11 to 14 V |
| IGSW (A12-28) - E1 (B32-104) | B - BR | Engine switch signal | Engine switch on (IG) | 11 to 14 V |
| E1 (B32-104) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
| E02 (B32-44) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| E04 (B32-46) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| E01 (B32-45) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the A12 and B32 ECM connectors.
Measure the voltage of the connectors.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| STA (A12-48) - E1 (B32-104) | LG - BR | Starter relay operation signal | Cranking | 5.5 V or more |
| ACCR (A12-13) - E1 (B32-104) | LG - BR | ACC relay cut signal (output) | Engine switch on (IG) → Cranking | 11 to 14 V → Below 1 V |
| TACH (A12-15) - E1 (B32-104) | GR - BR | Engine revolution signal (output) | Idling | Pulse generation (see waveform 1) |
| STAR (B32-52) - E1 (B32-104) | W - BR | Starter relay drive signal | Cranking | 11 to 14 V |
Inspect the connector using an oscilloscope.
![]() |
Waveform 1
| Item | Content |
| Symbols (Terminal No.) | TACH (A12-15) - E1 (B32-104) |
| Tool Setting | 5 V/DIV., 10 msec./DIV. |
| Condition | Engine idling |
| CHECK STEERING LOCK ECU |

Disconnect the E6 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| B (E6-7) - Body ground | L - Body ground | +B power supply | Always | Always |
| IG2 (E6-6) - Body ground | B - Body ground | Ignition power supply | Engine switch on (IG) | Always |
| IG2 (E6-6) - Body ground | B - Body ground | Ignition power supply | Engine switch off | Below 1 V |
| GND (E6-1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| SGND (E6-2) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E6 ECU connector.
Measure the voltage of the connector.
| Symbols (Terminal No.) | Wiring Color | Terminal Description | Condition | Specified Condition |
| SLP1 (E6-4) - GND (E6-1) | G - W-B | Steering lock actuator position signal | Steering lock locked | 11 to 14 V |
| SLP1 (E6-4) - GND (E6-1) | G - W-B | Steering lock actuator position signal | Steering lock released | Below 1 V |