DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
DTC P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
DTC P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
DTC P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2238 P2241 |
(1 trip detection logic): (a) AF+ voltage is 0.5 V or less (b) (AF+) - (AF-) = 0.1 V or less
(2 trip detection logic) |
|
| P2239 P2242 | AF+ voltage is more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| P2252 P2255 | AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic) |
|
| P2253 P2256 | AF- voltage is more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +25 % | Rich | Less than 3.0 V |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5 % | Lean | More than 3.35 V |
| O2S B1S2 or O2S B2S2 (HO2) | +25 % | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5 % | Lean | Less than 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HA1A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA1A (1) - A1A- (4) | - | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HA2A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA2A (1) - A2A- (4) | - | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| HA1A (B7-1) - HA1A (B96-86) | Below 1 Ω |
| A1A+ (B7-3) - A1A+ (B96-93) | Below 1 Ω |
| A1A- (B7-4) - A1A- (B96-116) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA2A (B67-1) - HA2A (B96-109) | Below 1 Ω |
| A2A+ (B67-3) - A2A+ (B96-120) | Below 1 Ω |
| A2A- (B67-4) - A2A- (B96-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (B7-1) or HA1A (B96-86) - Body ground | 10 kΩ or higher |
| A1A+ (B7-3) or A1A+ (B96-93) - Body ground | 10 kΩ or higher |
| A1A- (B7-4) or A1A- (B96-116) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA2A (B67-1) or HA2A (B96-109) - Body ground | 10 kΩ or higher |
| A2A+ (B67-3) or A2A+ (B96-120) - Body ground | 10 kΩ or higher |
| A2A- (B67-4) or A2A- (B96-119) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| No output | B |
|
| ||||
| A | |
| 4.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 5.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / DTC.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2A00 and/or P2A03 | B |
|
| ||||
| A | ||
| ||