DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2238 |
(2 trip detection logic): (a) AF+ voltage 0.5 V or less (b) (AF+) - (AF-) = 0.1 V or less
(2 trip detection logic) |
|
| P2239 | AF+ voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| P2252 | AF- voltage 0.5 V or less for 5.0 seconds or more (2 trip detection logic) |
|
| P2253 | AF- voltage more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1 S1 (A/F) | +25% | Rich | Less than 3.0 |
| -12.5% | Lean | More than 3.35 | |
| O2S B1 S2 (HO2) | +25% | Rich | More than 0.5 |
| -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the B7 A/F sensor connector.
Measure the resistance of the A/F sensor connector.
| Tester Connection | Specified Condition |
| HA1A (1) - +B (2) | 1.8 Ω to 3.4 Ω at 20°C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.INSPECT INTEGRATION RELAY (EFI MAIN RELAY) |
Remove the integration relay from the engine room relay block.
Inspect the EFI MAIN fuse.
![]() |
Remove the EFI MAIN fuse from the integration relay.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
Inspect the EFI MAIN relay.
Measure the EFI MAIN relay resistance.
| Tester Connection | Specified Condition |
| 1C-1 - 1A-4 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1A-2 and 1A-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the B7 A/F sensor connector.
Turn the ignition switch on (IG).
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (B7-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the B32 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| HA1A (B7-1) - HA1A (B32-109) | Below 1 Ω |
| A1A+ (B7-3) - A1A+ (B32-112) | Below 1 Ω |
| A1A- (B7-4) - A1A- (B32-113) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HA1A (B7-1) or HA1A (B32-109) - Body ground | 10 kΩ or higher |
| A1A+ (B7-3) or A1A+ (B32-112) - Body ground | 10 kΩ or higher |
| A1A- (B7-4) or A1A- (B32-113) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 4.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 5 minutes or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read pending DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2238, P2239, P2252 or P2253 | B |
|
| ||||
| A | ||
| ||