Home › TRANSMISSION ยท U151F AUTOMATIC TRANSAXLE › OIL PUMP

OIL PUMP > DISASSEMBLY

for Preparation Click here



1. INSPECT OIL PUMP ASSEMBLY


    D009205E01
  1. Turn the drive gear with 2 screwdrivers and make sure that it rotates smoothly.

    NOTICE:
    Be careful not to damage the lip of the oil seal.



2. REMOVE CLUTCH DRUM OIL SEAL RING


    D003650E02
  1. Remove the 2 clutch drum oil seal rings.



3. REMOVE STATOR SHAFT ASSEMBLY


    D003651E01
  1. Using a "TORX" socket wrench T30, remove the 11 bolts and stator shaft.



4. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY


    D009207E02
  1. Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the body clearance between the driven gear and oil pump body.

    Standard body clearance:
    0.10 to 0.17 mm (0.0039 to 0.0067 in.)

    Maximum body clearance:
    0.17 mm (0.0067 in.)

    If the body clearance is greater than the maximum, replace the oil pump body sub-assembly.



    D009208E01
  1. Using a feeler gauge, measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.07 to 0.15 mm (0.0028 to 0.0059 in.)

    Maximum tip clearance:
    0.15 mm (0.0059 in.)

    If the tip clearance is greater than the maximum, replace the oil pump body.



    D009209E01
  1. Using a straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.0020 in.)

    Maximum side clearance:
    0.05 mm (0.0020 in.)

    Standard drive gear thickness:
    Mark
    Thickness
    A
    11.690 to 11.699 mm (0.4602 to 0.4606 in.)
    B
    11.700 to 11.709 mm (0.4606 to 0.4610 in.)
    C
    11.710 to 11.720 mm (0.4610 to 0.4614 in.)
    D
    11.721 to 11.730 mm (0.4615 to 0.4618 in.)
    E
    11.731 to 11.740 mm (0.4619 to 0.4622 in.)

    Standard driven gear thickness:
    Mark
    Thickness
    A
    11.690 to 11.699 mm (0.4602 to 0.4606 in.)
    B
    11.700 to 11.709 mm (0.4606 to 0.4610 in.)
    C
    11.710 to 11.720 mm (0.4610 to 0.4614 in.)
    D
    11.721 to 11.730 mm (0.4615 to 0.4618 in.)
    E
    11.731 to 11.740 mm (0.4619 to 0.4622 in.)



5. REMOVE FRONT OIL PUMP DRIVE GEAR


    D009206E02
  1. Remove the front oil pump drive gear from the oil pump body.



6. REMOVE FRONT OIL PUMP DRIVEN GEAR


    C119012
  1. Remove the front oil pump driven gear from the oil pump body.



7. REMOVE FRONT OIL PUMP BODY O-RING


    D025586E02
  1. Using a screwdriver, pry out the O-ring.

    HINT:
    Tape the screwdriver tip before use.



8. REMOVE FRONT OIL PUMP OIL SEAL


    D003647E01
  1. Mount the oil pump in a soft jaw vise.

  1. Using SST, remove the oil seal from the oil pump body.

    SST
    09308-00010