Home › TRANSMISSION ยท U151F AUTOMATIC TRANSAXLE › UNDERDRIVE PLANETARY GEAR

UNDERDRIVE PLANETARY GEAR > REASSEMBLY

for Preparation Click here



1. INSTALL UNDERDRIVE PLANETARY RING GEAR


    D008112E02
  1. Install a new snap ring to the outer race of the radial ball bearing rear.

    HINT:
    When replacing the bearing, also replace the counter driven gear with a new one.



    D008113E01
  1. Using a piston ring compressor, squeeze the snap ring.



    D008114E01
  1. Using SST and a press, press in the outer race of the radial ball bearing rear.

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure not to damage the snap ring during outer race installation.



    D003827E04
  1. Install the underdrive planetary ring gear to the counter driven gear.



    D008115E02
  1. Using snap ring pliers, install the snap ring.



2. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY


    D026435E01
  1. Using SST and a press, install the angular ball bearing rear to the underdrive planetary gear.

    SST
    09502-12010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the bearing until it sits flush against the underdrive planetary gear.



    D008117E01
  1. Install the counter driven gear with planetary ring gear to the underdrive planetary gear.



    D026436E01
  1. Using SST and a press, install the angular ball bearing front.

    SST
    09502-12010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the counter driven gear while rotating it.



    D026433E01
  1. Using SST and a press, install the parking lock gear.

    SST
    09502-12010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the counter driven gear while rotating it.



3. INSTALL DIFFERENTIAL DRIVE PINION


    C140283E01
  1. Using SST and a press, install the differential drive pinion.

    SST
    09726-40010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    1. Check the position and number of the grooves on each end face of the differential drive pinion gear.
    2. Press the counter driven gear while rotating it.



4. INSTALL CYLINDRICAL ROLLER BEARING RACE INNER


    D026432E01
  1. Using SST and a press, install the cylindrical roller bearing race inner.

    SST
    09506-35010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the counter driven gear while rotating it.



5. INSTALL FRONT PLANETARY GEAR NUT


    D025609E04
  1. Place the underdrive planetary gear in a soft jaw vise.

    NOTICE:
    Be careful not to damage the differential drive pinion.

  1. Using a socket wrench, install a new lock nut.

    Torque:
    280 N*m{ 2855 kgf*cm , 207 ft.*lbf }



    C056809E01
  1. Using a pin punch and hammer, stake the lock nut.

    NOTICE:
    Make sure that there are no cracks on the nut.



6. INSPECT UNDERDRIVE PLANETARY GEAR PRELOAD


    D025593E02
  1. Using SST, secure the underdrive planetary gear.

    SST
    09387-00050  



    D025594E01
  1. Using SST and a torque wrench, measure the turning torque of the underdrive planetary gear assembly while rotating the torque wrench at 60 rpm.

    SST
    09387-00050  

    Torque:
    Standard turning torque at 60 rpm:
    0.50 to 1.42 N*m{ 5.1 to 14.5 kgf*cm , 4.4 to 12.6 in.*lbf }