SFI SYSTEM > Fuel Injector Circuit |

| 1.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | B16-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 2 | B15-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 3 | B14-1 - Ground | Ignition switch ON | 11 to 14 V |
| No. 4 | B13-1 - Ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
Turn the ignition switch off.
Reconnect the fuel injector assembly connectors.
|
| ||||
| OK | |
| 2.INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assembly .
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B16-2 - B32-108 (#10) | Always | Below 1 Ω |
| B15-2 - B32-107 (#20) | Always | Below 1 Ω |
| B14-2 - B32-106 (#30) | Always | Below 1 Ω |
| B13-2 - B32-105 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B16-2 or B32-108 (#10) - Body ground | Always | 10 kΩ or higher |
| B15-2 or B32-107 (#20) - Body ground | Always | 10 kΩ or higher |
| B14-2 or B32-106 (#30) - Body ground | Always | 10 kΩ or higher |
| B13-2 or B32-105 (#40) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - FUEL INJECTOR ASSEMBLY) |
Disconnect the fuel injector assembly connectors.
Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B16-1 - IG2 relay (IG2) terminal 5 | Always | Below 1 Ω |
| B15-1 - IG2 relay (IG2) terminal 5 | Always | Below 1 Ω |
| B14-1 - IG2 relay (IG2) terminal 5 | Always | Below 1 Ω |
| B13-1 - IG2 relay (IG2) terminal 5 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B16-1 or IG2 relay (IG2) terminal 5 - Body ground | Always | 10 kΩ or higher |
| B15-1 or IG2 relay (IG2) terminal 5 - Body ground | Always | 10 kΩ or higher |
| B14-1 or IG2 relay (IG2) terminal 5 - Body ground | Always | 10 kΩ or higher |
| B13-1 or IG2 relay (IG2) terminal 5 - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel injector connector.
Reinstall the IG2 relay.
|
| ||||
| OK | ||
| ||