Home › ENGINE · 2GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P1550    Battery Current Sensor Circuit

DTC    P1551    Battery Current Sensor Circuit Low

DTC    P1552    Battery Current Sensor Circuit High

for Preparation Click here


DESCRIPTION

A110645E01
The battery current sensor installed on the negative (-) battery terminal detects the amount of current supplied from the generator.
The battery current sensor changes current to voltage (at the negative (-) battery terminal) and sends it to the ECM. The ECM controls the voltage of the generator based on the signals from the battery current sensor.

DTC No.
DTC Detection Condition
Trouble Area
P1550
The following condition continues for 10 seconds or more with the ignition switch to the ON position
(1 trip detection logic):
  1. Difference between the maximum and minimum current values of the battery current sensor is 1 A or less
  1. Open or short in battery current sensor circuit
  2. Battery current sensor assembly
  3. ECM
P1551
Battery current sensor output value is 0.2 V or less for 0.5 seconds or more with the ignition switch to the ON position
(1 trip detection logic):
  1. Short in battery current sensor circuit
  2. Battery current sensor assembly
  3. ECM
P1552
Battery current sensor output value is 4.8 V or more for 0.5 seconds or more with the ignition switch to the ON position
(1 trip detection logic):
  1. Open in battery current sensor circuit
  2. Battery current sensor assembly
  3. ECM

WIRING DIAGRAM


A136444E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.INSPECT BATTERY CURRENT SENSOR ASSEMBLY


    A124656E08
  1. Disconnect the battery current sensor connector.

  1. Measure the resistance of the battery current sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    VC5 (2) - E2 (4)
    0.1 to 10 kΩ
    VC5 (2) - IB (3)
    Below 0.5 kΩ
    IB (3) - E2 (4)
    0.05 to 10 kΩ



NG
REPLACE BATTERY CURRENT SENSOR ASSEMBLY
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR - ECM)


    A127962E20
  1. Disconnect the battery current sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    IB (B31-3) - IB (B96-100)
    Below 1 Ω
    VC5 (B31-2) - VCIB (B96-80)
    Below 1 Ω
    E2 (B31-4) - EIB (B96-101)
    Below 1 Ω
    THB (B31-1) - THB (B96-103)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    IB (B31-3) or IB (B96-100) - Body ground
    10 kΩ or higher
    VC5 (B31-2) or VCIB (B96-80) - Body ground
    10 kΩ or higher
    THB (B31-1) or THB (B96-103) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)