POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH |

| 1.INSPECT FUSE (RL DOOR) |
Remove the RL DOOR fuse from the instrument panel junction block.
Measure the resistance of the fuse.
|
| ||||
| OK | |
| 2.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH) (POWER SOURCE) |
![]() |
Disconnect the J1 switch connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
| J1-3 (B) - Body ground | Ignition switch on (IG) | 10 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH) |
![]() |
Remove the power window regulator switch.
Measure the resistance of the switch when the switch is operated.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (D) - 2 (SD) 3 (B) - 4 (U) | UP | Below 1 Ω |
| 4 (U) - 5 (SU) 1 (D) - 2 (SD) | OFF | Below 1 Ω |
| 1 (D) - 3 (B) 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (REGULATOR SWITCH - REGULATOR MOTOR) |

Disconnect the J1 switch connector.
Disconnect the J3 motor connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| J1-4 (U) - J3-1 (U) | Below 1 Ω |
| J1-1 (D) - J3-2 (D) | Below 1 Ω |
| J1-4 (U) or J3-1 (U) - Body ground | 10 kΩ or higher |
| J1-1 (D) or J3-2 (D) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH) |
![]() |
Remove the power window regulator motor.
Apply the battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
| Battery positive (+) → 1 Battery negative (-) → 2 | Motor gear rotates clockwise |
| Battery positive (+) → 2 Battery negative (-) → 1 | Motor gear rotates counterclockwise |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (MASTER SWITCH - REGULATOR SWITCH) |

Disconnect the H2*1 or G8*2 switch connector.
Disconnect the J1 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
| H2-12 (U) - J1-5 (SU) | Below 1 Ω |
| H2-13 (D) - J1-2 (SD) | Below 1 Ω |
| H2-12 (U) or J1-5 (SU) - Body ground | 10 kΩ or higher |
| H2-13 (D) or J1-2 (SD) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| G8-18 (U) - J1-5 (SU) | Below 1 Ω |
| G8-10 (D) - J1-2 (SD) | Below 1 Ω |
| G8-18 (U) or J1-5 (SU) - Body ground | 10 kΩ or higher |
| G8-10 (D) or J1-2 (SD) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||