Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for HDD)

NAVIGATION SYSTEM (for HDD) > TERMINALS OF ECU

for Preparation Click here



CHECK NAVIGATION RECEIVER ASSEMBLY

E178165E04

  1. Disconnect the E52 navigation receiver connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E52-3 (ACC) - E52-7 (GND)
    GR - BR
    Accessory (On)
    Ignition switch off
    Below 1 V
    E52-3 (ACC) - E52-7 (GND)
    GR - BR
    Accessory (On)
    Ignition switch ACC
    11 to 14 V
    E52-4 (B) - E52-7 (GND)
    L - BR
    Battery
    Always
    11 to 14 V
    E52-7 (GND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E52 navigation receiver connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E52-1 (FR+) - E52-7 (GND)
    LG - BR
    Sound signal (Front Right)
    Audio system playing
    A waveform synchronized with the sound is output
    E52-2 (FL+) - E52-7 (GND)
    P - BR
    Sound signal (Front Left)
    Audio system playing
    A waveform synchronized with the sound is output
    E52-5 (FR-) - E52-7 (GND)
    L - BR
    Sound signal (Front Right)
    Audio system playing
    A waveform synchronized with the sound is output
    E52-6 (FL-) - E52-7 (GND)
    V - BR
    Sound signal (Front Left)
    Audio system playing
    A waveform synchronized with the sound is output
    E52-10 (ILL+) - E52-7 (GND)
    G - BR
    Illumination signal
    Light control switch off
    Below 1 V
    Light control switch on
    11 to 14 V
    E53-1 (RR+) - E52-7 (GND)
    R - BR
    Sound signal (Rear Right)
    Audio system playing
    A waveform synchronized with the sound is output
    E53-2 (RL+) - E52-7 (GND)
    B - BR
    Sound signal (Rear Left)
    Audio system playing
    A waveform synchronized with the sound is output
    E53-3 (RR-) - E52-7 (GND)
    W - BR
    Sound signal (Rear Right)
    Audio system playing
    A waveform synchronized with the sound is output
    E53-6 (RL-) - E52-7 (GND)
    Y - BR
    Sound signal (Rear Left)
    Audio system playing
    A waveform synchronized with the sound is output
    E57-1 (PKB) - E52-7 (GND)
    B - BR
    Parking brake signal
    See "Vehicle Signal Check Mode" (Click here)
    -
    E57-3 (SPD) - E52-7 (GND)
    V - BR
    Speed signal from combination meter
    See "Vehicle Signal Check Mode" (Click here)
    -
    E57-4 (BTCY)*2 - E52-7 (GND)
    LG - BR
    Back door courtesy light signal
    See "Vehicle Signal Check Mode" (Click here)
    -
    E57-5 (REV) - E52-7 (GND)
    R - BR
    Reverse signal
    See "Vehicle Signal Check Mode" (Click here)
    -
    E106-1 (V+)*2 - E106-11 (V-)
    W - R
    Display signal
    Ignition switch ON, shift lever in R
    Pulse generation (Refer to waveform 1)
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
    Pulse generation (Refer to waveform 2)
    E106-2 (CA+)*2 - E52-7 (GND)
    B - BR
    Television camera power supply
    Ignition switch ON, shift lever in R
    5.8 to 6.2 V
    E106-3 (SNS2) - E52-7 (GND)
    W-B - BR
    Microphone connection detection signal
    Always
    Below 1 V
    E106-4 (MIN+) - E52-7 (GND)
    W - BR
    Microphone voice signal
    See "Microphone & Voice Recognition Check" (Click here)
    -
    E106-5 (MACC) - E52-7 (GND)
    B - BR
    Microphone amplifier power supply
    Ignition switch off
    Below 1 V
    Ignition switch ACC
    4.75 to 5.25 V
    E106-6 (SWG) - Body ground
    B - Body ground
    Steering pad switch ground
    Always
    Below 1 V
    E106-7 (SW1) - E106-6 (SWG)
    W - B
    Steering pad switch signal
    No switch is pushed
    → SEEK+ switch pushed
    → SEEK- switch pushed
    → VOL+ switch pushed
    → VOL- switch pushed
    2.97 to 3.56 V
    → 0.27 to 0.35 V
    → 0.86 to 1.03 V
    → 1.51 to 1.79 V
    → 2.22 to 2.66 V
    E106-8 (SW2) - E106-6 (SWG)
    R - B
    Steering pad switch signal
    No switch is pushed
    → MODE switch pushed
    → On Hook switch pushed
    → Off Hook switch pushed
    → Voice switch pushed
    2.97 to 3.56 V
    → 0.27 to 0.35 V
    → 0.86 to 1.03 V
    → 1.51 to 1.79 V
    → 2.22 to 2.66 V
    E106-11 (V-)*2 - E106-12 (CGND)
    R - Shielded
    Ground
    Always
    Below 1 V
    E106-12 (CGND)*2 - Body ground
    Shielded - Body ground
    Ground
    Always
    Below 1 V
    E106-13 (MIN-) - E52-7 (GND)
    R - BR
    Microphone voice signal
    See "Microphone&Voice Recognition Check" (Click here)
    -
    E106-14 (SGND) - E52-7 (GND)
    Shielded - BR
    Signal ground
    Always
    Below 1 V
    E106-15 (ARI) - E52-7 (GND)
    W - BR
    Sound signal (Right)
    External device playing (when stereo jack is used)
    A waveform synchronized with the sound is input
    E106-16 (ASGN) - E52-7 (GND)
    R - BR
    Ground
    Always
    Below 1 V
    E106-17 (ALI) - E52-7 (GND)
    B - BR
    Sound signal (Left)
    External device playing (when stereo jack is used)
    A waveform synchronized with the sound is input
    E106-18 (AGND) - Body ground
    Shielded - Body ground
    Shielded ground
    Always
    Below 1 V
    E106-19 (AUXI) - E52-7 (GND)
    R - BR
    External device connection detection signal
    External device connected
    1.1 to 1.5 V
    External device is not connected
    2.0 to 2.4 V
    E106-20 (LRHD)*1 - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    *1: for RHD
    *2: w/ Rear View Monitor System

    1. If the result is not as specified, the navigation receiver assembly may have a malfunction.



  5. E159949E01
  6. Using an oscilloscope, check waveform 1.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    E106-1 (V+) - E106-11 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    Ignition switch ON, shift lever in R



  7. E164781E01
  8. Using an oscilloscope, check waveform 2.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    E106-1 (V+) - E106-11 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    Ignition switch ON, shift lever in R, screen blacked out by covering camera lens