CONTINUOUSLY VARIABLE TRANSAXLE FLUID > ADJUSTMENT |
| 1. PRECAUTIONS AND WORK DESCRIPTION |
The K111F continuously variable transaxle does not have an oil filler tube or oil level gauge. When adding fluid, add fluid through the refill hole in the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the oil pan.
When adding fluid, add the specified amount of fluid while the engine is cold. Then, warm up the engine to circulate the fluid in the transaxle and adjust the fluid level with the engine idling at the specified fluid temperature.
The K111F continuously variable transaxle requires Toyota Genuine CVT fluid TC.
When adjusting the fluid level, park the vehicle on level ground. Make sure that the longitudinal tilt of the vehicle is not more than 1°.
When adjusting the fluid level, turn off all electrical devices, such as the air conditioning, headlights and electric fan, to reduce electrical load.
The fluid temperature in the text indicates "A/T Oil Temperature 1" displayed on the intelligent tester.
Perform the adjustment according to the following procedures and notes.

| 2. WORK FLOW |
The adjustment should be performed according to the procedures referenced in the work flow below.

| 3. BEFORE FILLING TRANSAXLE WITH FLUID |
![]() |
Lift the vehicle.
Remove the No. 1 engine under cover and rear engine under cover LH.
| 4. PERFORM INITIAL FILLING |
| Operations that do not Require Initial Filling |
|
![]() |
Remove the refill plug and gasket from the continuously variable transaxle.
![]() |
Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the continuously variable transaxle.
![]() |
Using a 6 mm socket hexagon wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.
Perform initial filling.
![]() |
Fill fluid into the refill hole until it flows out from the overflow plug hole.
![]() |
Wait until the fluid flow slows and only drops come out.
Temporarily install the overflow plug.
| 5. ADD SPECIFIED AMOUNT OF FLUID |
Remove the refill plug and gasket from the continuously variable transaxle (when initial filling is not performed).
Fill fluid into the refill hole with the correct amount of fluid as listed in the table below.
| Operation Performed | Fill Amount |
| 0.6 liters (0.6 US qts, 0.5 Imp. qts) |
| Installation of a new transaxle (use of new torque converter). | 6.2 liters (6.6 US qts, 5.5 Imp. qts) |
| Installation of a new transaxle (reuse of torque converter). | 5.6 liters (5.9 US qts, 4.9 Imp. qts) |
| 2.1 liters (2.2 US qts, 1.8 Imp. qts) |
| Removal and installation of a torque converter (use of new torque converter). | 3.4 liters (3.6 US qts, 3.0 Imp. qts) |
| Removal and installation of a torque converter (reuse of torque converter). | 2.9 liters (3.1 US qts, 2.6 Imp. qts) |
![]() |
Temporarily install the refill plug to avoid fluid spillage.
Lower the vehicle.
| 6. ADJUST FLUID TEMPERATURE |
When using the intelligent tester:
Connect the intelligent tester to the DLC3 with the ignition switch off.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.
According to the display on the intelligent tester, perform the Active Test "Connect the TC and TE1".
When not using the intelligent tester:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.
| *1 | Front view of DLC3 |
Depress and hold the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds).
![]() |
While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.
![]() |
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
Disconnect the terminals of the DLC3.
When using the intelligent tester.
Enter the following menus: Connect the TC and TE1 / OFF.
When not using the intelligent tester.
Remove SST from terminals 13 (TC) and 4 (CG).
Adjust the fluid temperature to the normal operating temperature.
Check the fluid temperature by the D shift indicator.
Adjust the fluid temperature.
| Below Normal Operating Temperature | Normal Operating Temperature | Above Normal Operating Temperature | |
| Fluid Temperature ("A/T Oil Temperature 1" displayed on the intelligent tester) | 30°C or less (86°F or less) | 30 to 40°C (86 to 104°F) | 40°C or higher (104°F or higher) |
| D Shift Indicator | Off | On | Blinks |
| 7. ADJUST FLUID LEVEL |
Lift the vehicle.
![]() |
Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket.
Check the amount of fluid that comes out of the overflow plug hole.
![]() |
*2: If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add transaxle fluid through the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drops come out.
![]() |
*1: If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drops come out.
![]() |
Install a new gasket and the overflow plug.
![]() |
Install a new gasket and the refill plug.
Lower the vehicle.
Turn the ignition switch off.
Remove the intelligent tester from the DLC3 (when using the intelligent tester).
| 8. AFTER FILLING TRANSAXLE |
Lift the vehicle.
Clean each part.
Check for fluid leaks.
Install the No. 1 engine under cover and rear engine under cover LH.
Lower the vehicle.