WINDSHIELD GLASS > INSTALLATION |
| 1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER |
Apply Primer G to the glass where the spacers will be installed.
Install 2 new spacers onto the glass as shown in the illustration.

| Area | Specified Condition |
| a | 7.7 mm (0.303 in.) |
| b | 40.0 mm (1.575 in.) |
| 2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER |
![]() |
Install 2 new stoppers to the vehicle body as shown in the illustration.
| 3. INSTALL WINDOW GLASS ADHESIVE DAM |
Apply Primer G to the glass where the glass adhesive dams will be installed.
Remove the peeling paper from the adhesive part of the dam. Install the dam (adhesive side) to the glass (Primer G area), but exclude the spacer area A as shown in the illustration.

| Area | Specified Condition |
| a | 11.5 mm (0.452 in.) |
| 4. INSTALL FRONT WINDOW MOULDING INNER CENTER |
![]() |
Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.
Install the windshield outside moulding, as shown in the illustration.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
| 5. INSTALL WINDSHIELD GLASS |
![]() |
Position the glass.
Using suction cups, place the glass in the correct position.
Check that the entire contact surface of the glass rim is perfectly even.
Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.
Using suction cups, remove the glass.
![]() |
Using a brush, apply Primer M to the exposed part of the vehicle body.
Using a brush or sponge, apply Primer G to the contact surface of the glass.

Apply adhesive to the glass.
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.

| Area | Specified Condition |
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 5.0 mm (0.196 in.) |
| d | 28.3 mm (1.114 in.) |
![]() |
Install the glass to the vehicle body.
Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.
Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.
Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.
w/ Windshield Deicer:
Install the clip and connect the connector.
| 6. INSTALL COWL TOP VENTILATOR LOUVER |
![]() |
Attach the 12 claws and install the louver.
Install the 2 clips.
| 7. INSTALL NO. 2 WINDSHIELD OUTSIDE MOULDING FASTENER |
![]() |
Install the moulding fastener with the 2 clips and double-sided tape.
| 8. INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING FASTENER |
Install the moulding fastener with the 2 clips and double-sided tape.
| 9. INSTALL NO. 2 WINDSHIELD MOULDING OUTSIDE LH |
![]() |
Install the moulding with claw and clip.
| 10. INSTALL NO. 2 WINDSHIELD MOULDING OUTSIDE RH |
Install the moulding with claw and clip.
| 11. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
![]() |
Attach the claw to install the front fender to cowl side seal.
| 12. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
![]() |
Attach the claw to install the front fender to cowl side seal.
| 13. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration with a wire brush.
![]() |
Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.
Operate the front wipers while spraying water or washer fluid on the windshield. Ensure that there is no interference between the blades and pillar.
| 14. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Stop the wiper motor at the automatic stop position.
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration with a wire brush.
![]() |
Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.
| 15. INSTALL FRONT WIPER ARM HEAD CAP |
Install the 2 caps.
| 16. INSTALL ROOF HEADLINING ASSEMBLY (for Short Body) |
Install the roof headlining .
| 17. INSTALL ROOF HEADLINING ASSEMBLY (for Long Body) |
Install the roof headlining .
| 18. INSTALL VISOR HOLDER |
![]() |
Set the claws of the visor holder as shown in the illustration.
Insert the visor holder to install it.
| 19. INSTALL VISOR ASSEMBLY LH |
![]() |
Attach the 2 claws to install the visor.
Install portion A of the visor to the visor holder.
Attach the 4 claws to install the visor bracket cover.
| 20. INSTALL VISOR ASSEMBLY RH |
| 21. INSTALL ASSIST GRIP SUB-ASSEMBLY |
![]() |
Attach the 4 claws to install the assist grip.
| 22. INSTALL ASSIST GRIP COVER |
Attach the 4 claws to install the 2 assist grip covers.
| 23. INSTALL ROOM LIGHT ASSEMBLY |
![]() |
Attach the 4 claws to install the room light switch base.
![]() |
Attach the 4 claws to install the room light.
![]() |
Install the bulb to the room light switch base.
![]() |
Attach the 4 claws and install the 2 covers.
| 24. INSTALL RAIN SENSOR |
![]() |
If reusing the sensor:
Install new sensor tape.
Remove the used sensor tape from the windshield glass or sensor.
Apply new sensor tape on the lens surface of the sensor indicated by the hatched line.
| Area | Specified condition |
| A | 13.5 mm (0.5315 in.) |
| B | 7.25 mm (0.2854 in.) |
![]() |
Attach the sensor body.
![]() |
Push in the stopper.
Connect the wire connector.
![]() |
Push in the cover.
| 25. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror) |
![]() |
Slide and install the inner rear view mirror as shown in the illustration.
Install the cover.
| 26. INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror) |
![]() |
w/o Rear Monitor:
Using a T20 "TORX" socket wrench, install the inner rear view mirror with the screw.
Connect the connector.
Install the inner rear view mirror stay holder cover.
w/ Rear Monitor:
![]() |
Using a T20 "TORX" socket wrench, install the inner rear view mirror with the screw.
Connect the connector.
Install the inner rear view mirror stay holder cover.
| 27. INSTALL FRONT PILLAR GARNISH LH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 wire harness clamps.
![]() |
w/ Curtain Shield Airbag:
Attach the 3 guides.
Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.
![]() |
Attach the 2 clips to install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Attach the 2 clips and 3 guides to install the front pillar garnish.
| 28. INSTALL FRONT PILLAR GARNISH RH |
w/ Curtain Shield Airbag:
Remove the piece of cloth or nylon.
![]() |
Install the 4 antenna cord clamps.
![]() |
w/ Curtain Shield Airbag:
Attach the 3 guides.
Turn the end of the front pillar garnish clip 90° with needle-nose pliers and install it to the front pillar garnish.
![]() |
Attach the 2 clips to install the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Attach the 2 clips and 3 guides to install the front pillar garnish.
| 29. INSTALL FRONT DOOR OPENING TRIM LH |
| 30. INSTALL FRONT DOOR OPENING TRIM RH |
| 31. CHECK FOR LEAKS AND REPAIR |
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
| 32. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |