Home › BODY › EXTERIOR › FRONT BUMPER (w/ Hood Moulding)

FRONT BUMPER (w/ Hood Moulding) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT BUMPER SIDE RETAINER LH


B252774
  1. Attach the claw to install the front bumper side retainer.

  1. Install the bolt and clip.



2. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure described for the LH side.



3. INSTALL FRONT BUMPER REINFORCEMENT


    B252782
  1. Install the front bumper reinforcement with the 8 bolts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }

  1. Attach the 2 clamps to install the wire harness.

  1. Attach the clamp to install the cooler thermistor.



4. INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY


B252781
  1. Install the reinforcement with the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



5. INSTALL LOW PITCHED HORN ASSEMBLY


B252780
  1. Install the horn with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Connect the horn connector.



6. INSTALL HIGH PITCHED HORN ASSEMBLY


B252779
  1. Install the horn with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Connect the horn connector.



7. INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY


B252778
  1. Install the front bumper center stay with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



8. INSTALL FRONT BUMPER LOWER ABSORBER


B252777
  1. Install the front bumper lower absorber.



9. INSTALL FRONT BUMPER ENERGY ABSORBER LH


B252776
  1. Install the front bumper energy absorber.



10. INSTALL FRONT BUMPER ENERGY ABSORBER RH

HINT:
Use the same procedure described for the LH side.



11. INSTALL FRONT BUMPER NO. 2 ENERGY ABSORBER


B252775
  1. Install the front bumper No. 2 energy absorber.



12. INSTALL FRONT BUMPER COVER


    B254536
  1. w/ Headlight Cleaner System:
    Connect the headlight cleaner hose.

  1. Connect the 2 fog light connectors.

  1. Attach the 4 claws to install the front bumper cover.



    B254517
  1. w/ Diffuser:
    Install the 4 clips and 8 screws.



    B255284
  1. w/o Diffuser:
    Install the 4 clips and 8 screws.



    B254462
  1. Position the groove on the pin hold clip vertically and insert the clip to install it.

    NOTICE:
    Make sure that the groove on the pin hold clip is positioned vertically.

    HINT:
    Use the same procedure for the RH and LH sides.



13. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH (w/ Diffuser)


B252770
  1. Install the front fender front splash shield with the nut, bolt and screw.



14. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH (w/ Diffuser)

HINT:
Use the same procedure described for the LH side.



15. INSTALL RADIATOR GRILLE PROTECTOR


B254516
  1. Install the 3 radiator grille protectors.



16. INSTALL RADIATOR SUPPORT OPENING COVER


B254515
  1. Install the radiator support opening cover with the 9 clips.