Home › ENGINE ยท 3ZR-FAE › FUEL › FUEL PUMP

FUEL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL FUEL PUMP ASSEMBLY


    A195890
  1. Connect the fuel pump connector.



    A197087E04
  1. Install the fuel pump spacer to the fuel pump assembly.
    Text in Illustration 
    *2
    Fuel Pump Spacer

  1. Apply gasoline to a new O-ring and install the O-ring to the fuel pump.
    Text in Illustration 
    *1
    New O-Ring



    A197085
  1. Attach the 5 claws to the holes to install the fuel pump.



2. INSTALL NO. 1 FUEL SUCTION SUPPORT


    A126126
  1. Attach the 2 claws to the holes to install the No. 1 fuel suction support.



3. INSTALL NO. 1 FUEL SUB-TANK


    A195888E03
  1. Apply gasoline to a new O-ring and install it to the jet pump.
    Text in Illustration 
    *1
    Jet Pump
    *2
    New O-Ring



    A130453
  1. Install the jet pump while aligning it with the installation position on the No. 1 fuel sub-tank.

  1. Install the jet pump nozzle.



    A126125
  1. Attach the 2 claws to the holes to install the No. 1 fuel sub-tank.



    A126123
  1. Connect the wire harness connector.



    A126684
  1. Install the 2 springs to the fuel suction plate shafts, and then install them to the No. 1 fuel sub-tank.



    A201342E01
  1. Using needle-nose pliers, install a new E-ring.

    HINT:
    Slightly lower the fuel suction plate to install the E-ring.



4. INSTALL FUEL SUCTION WITH PUMP ASSEMBLY


    A126699E03
  1. Install a new gasket onto the fuel suction with pump.
    Text in Illustration 
    *1
    New Gasket



    A202412E01
  1. Connect the fuel hose with the paint mark facing towards the top of the vehicle, and then secure the clip.

  1. Install the fuel suction with pump into the fuel tank.

    NOTICE:
    Do not damage the fuel suction with pump.



5. INSTALL FUEL TANK VENT TUBE SET PLATE


    A124675
  1. Install the set plate with the 8 bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



6. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A124668
  1. Install the fuel tube with the joint clip.

    NOTICE:
    A124131E05
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joint is inserted securely.
    3. Check that the fuel tube joint clip is on the collar of the fuel tube joint.
    4. After installing the tube joint clip, check that the fuel tube joint cannot be pulled off.
    5. Be careful not to damage the clip. If the clip is damaged, replace it.



7. CONNECT FUEL EMISSION HOSE


  1. Connect the purge line hose and air inlet line hose to the fuel suction plate.


    A213193E01


    Text in Illustration 
    *1
    Purge Line Hose
    *2
    Air Inlet Line Hose
    *3
    Fuel Emission Hose
    -
    -

    HINT:
    Make sure the direction of the hose clamps are as indicated in the illustration.

  1. Connect the fuel emission hose to the fuel suction plate.

    HINT:
    Firmly push the tube connector until a "click" sound is heard.

    NOTICE:
    1. Before connecting the hose, check if there is any damage or foreign matter in the hose or connector.
    2. Check that the connector is connected by pulling on it.



8. INSTALL FUEL TANK ASSEMBLY
  1. Install the fuel tank assembly (Click here).