Home › BODY › WINDSHIELD / WINDOWGLASS › BACK DOOR GLASS

BACK DOOR GLASS > INSTALLATION

for Preparation Click here



1. INSTALL BACK WINDOW GLASS SPACER
  1. Apply Primer G to the installation part of the clips.

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.



  1. Install the 4 new spacers onto the glass as shown in the illustration.


    B134612E01

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



2. INSTALL BACK WINDOW MOULDING OUTSIDE



B134610E02

  1. Apply Primer G to the installation part of the window moulding.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Install a new moulding as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    a
    3.0 mm (0.118 in.)
    b
    9.0 mm (0.354 in.)
    c
    9.0 to 11.0 mm (0.118 to 0.433 in.)



3. INSTALL BACK WINDOW MOULDING LOWER


    B273465E01
  1. Cut the back window moulding lower so that it is the size shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    a
    1285 mm (50.6 in.)

  1. Remove the release paper from the back window moulding lower.

  1. Apply Primer G to the installation part of the window moulding.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



    B273466E01
  1. Install a new moulding as shown in the illustration.

    Standard measurement:
    Area
    Specified Condition
    a
    7.3 mm (0.287 in.)



4. INSTALL BACK DOOR GLASS


B134614E01
  1. Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the back door glass.


    B131517E03

    Standard measurement:
    Area
    Specified Condition
    a
    10.4 mm (0.409 in.)
    b
    7.0 mm (0.275 in.)
    c
    35.5 mm (1.397 in.)
    d
    13.0 mm (0.511 in.)

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the back door glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or Equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration below.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the back door glass as shown in the illustration.


      B131518E01

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      10.4 mm (0.409 in.)
      d
      7.0 mm (0.275 in.)
      e
      35.5 mm (1.397 in.)
      f
      13.0 mm (0.511 in.)



  1. Install the back door glass to the vehicle body.

    1. Hold the back window glass in place securely with tape or equivalent until the adhesive has hardened.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check that the clips are attached to the vehicle body correctly.
      3. Check the clearance between the vehicle body and glass.

    2. Lightly press the front surface of the back door glass to ensure that the back door glass is securely fit to the vehicle body.



    3. BO03986E06
    4. Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

      NOTICE:
      Do not drive the vehicle within the time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



5. INSTALL REAR SPOILER
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

  1. If reusing the spoiler:
    Clean the spoiler.

    1. Using a heat light, heat the spoiler.

  1. Connect the center stop light connector.



    B127944
  1. Install the spoiler with 3 clips.



    B127943
  1. Install the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



6. INSTALL REAR WIPER MOTOR ASSEMBLY


B131460
  1. Install the wiper motor with the 3 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



7. INSTALL BACK DOOR TRIM BOARD
  1. Install the back door trim pocket with the 5 screws.



    B129943
  1. Attach the 13 clips to install the trim board.



8. INSTALL BACK DOOR SIDE GARNISH LH


    B129945
  1. Attach the 2 claws and 2 clips to install the garnish.



9. INSTALL BACK DOOR SIDE GARNISH RH

HINT:
Use the same procedure described for the LH side.



10. INSTALL BACK DOOR CENTER GARNISH


    B129944
  1. Attach the 4 claws and 4 clips to install the garnish.



11. INSTALL REAR WIPER ARM ASSEMBLY
  1. Stop the wiper motor at the automatic stop position.



    B117856E02
  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    E125268E03
  1. Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    1. Hold down the arm hinge by hand while tightening the nut.
    2. Install the arm and blade so that the rear wiper blade is aligned with the defogger line.



    B136379
  1. Install the cap.



12. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL