Home › BODY › WINDSHIELD / WINDOWGLASS › QUARTER WINDOW GLASS

QUARTER WINDOW GLASS > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL QUARTER WINDOW ASSEMBLY LH


B134600E02
  1. Using a brush or sponge, apply primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Using a brush or sponge, apply primer G to the contact surface of the glass.


    B134599E03



    B134602E01

    HINT:
    If primer is applied to an area that is specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the quarter window glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or Equivalent




    1. Cut off the tip of the cartridge nozzle as shown in the illustration.


      B134601E01



      B134598E01

      Standard measurement:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the quarter window glass as shown in the illustration.



  1. Install the quarter window glass to the vehicle body.

    1. Hold the quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check that the clips are attached to the body correctly.
      3. Check the clearance between the body and glass.

    2. Lightly press the front surface of the glass to ensure a close fit.



    3. BO03986E05
    4. Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

      NOTICE:
      Do not drive the vehicle within the time written in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



2. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



3. INSTALL ROOF HEADLINING ASSEMBLY (for Short Body)
  1. Install the roof headlining assembly .



4. INSTALL ROOF HEADLINING ASSEMBLY (for Long Body)
  1. Install the roof headlining assembly .



5. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH (for Short Body)


    B129714
  1. Attach the 7 clips to install the garnish.



6. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH (for Long Body)


    B129708
  1. Attach the 7 clips to install the garnish.



7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body)


B129712
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 5 clips and 5 claws to install the trim board.

  1. Install the bolt and 2 screws.



    B137546
  1. Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.



8. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body)


    B129706
  1. Install the belt hanger to the trim board.

  1. Connect the power outlet socket connector.

  1. Attach the 4 clips and 5 claws to install the trim board.

  1. Install the 2 screws and 2 bolts.



    B137546
  1. Connect the rear No.1 seat belt's floor anchor.

    1. Connect the floor anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Install the anchor cover.



9. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body)


B131615E01
  1. Align the bracket positioning hole with the claws and install the bracket with the bolt, 2 washers and collar.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



10. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body)


B131611
  1. Install the cover with the 4 claws.



11. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH


12. INSTALL REAR FLOOR FINISH PLATE (for Short Body)


    B129716
  1. Attach the 6 clips to install the finish plate.



13. INSTALL REAR FLOOR FINISH PLATE (for Long Body)


    B129704
  1. Attach the 2 claws and 6 clips to install the finish plate.



14. INSTALL BACK DOOR WEATHERSTRIP


15. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE


B129717
  1. Attach the 7 clips to install the side plate.

  1. Install the 4 screws.



16. INSTALL JACK CARRIER ASSEMBLY (for Short Body)


    B129715
  1. Install the jack carrier with the 7 clips.



17. INSTALL REAR NO. 2 FLOOR BOARD


18. INSTALL REAR NO. 3 FLOOR BOARD


19. INSTALL DECK BOARD ASSEMBLY


20. INSTALL REAR NO. 1 FLOOR BOARD


21. INSTALL TONNEAU COVER ASSEMBLY


22. INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY


23. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


24. INSTALL REAR DOOR SCUFF PLATE LH (for Short Body)


    B129711
  1. Attach the 8 claws to install the scuff plate.



25. INSTALL REAR DOOR SCUFF PLATE LH (for Long Body)


    B129703
  1. Attach the 9 claws and 2 clips to install the scuff plate.