QUARTER WINDOW GLASS > REMOVAL |
| 1. REMOVE REAR DOOR SCUFF PLATE LH (for Short Body) |
![]() |
Using a screwdriver, detach the 8 claws and remove the scuff plate.
| 2. REMOVE REAR DOOR SCUFF PLATE LH (for Long Body) |
![]() |
Using a screwdriver, detach the 9 claws.
Using a clip remover, detach the 2 clips and remove the garnish.
| 3. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the rear door opening trim weatherstrip.
| 4. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY |
Remove the package tray trim pocket.
| 5. REMOVE TONNEAU COVER ASSEMBLY |
Remove tonneau cover.
| 6. REMOVE REAR NO. 1 FLOOR BOARD |
Remove the rear floor No. 1 board.
| 7. REMOVE DECK BOARD ASSEMBLY |
Remove the deck board.
| 8. REMOVE REAR NO. 3 FLOOR BOARD |
Remove the rear floor No. 3 board.
| 9. REMOVE REAR NO. 2 FLOOR BOARD |
Remove the rear floor No. 2 board.
| 10. REMOVE JACK CARRIER ASSEMBLY (for Short Body) |
![]() |
Using a clip remover, remove the 7 clips and remove the jack carrier.
| 11. REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE |
![]() |
Remove the 4 screws.
Using a clip remover, detach the 7 clips and remove the plate.
| 12. REMOVE BACK DOOR WEATHERSTRIP |
Remove the back door weatherstrip.
| 13. REMOVE REAR FLOOR FINISH PLATE (for Short Body) |
![]() |
Using a clip remover, detach the 6 clips and remove the finish plate.
| 14. REMOVE REAR FLOOR FINISH PLATE (for Long Body) |
![]() |
Using a clip remover, detach the 6 clips.
Detach the 2 claws and remove the finish plate.
| 15. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH |
| 16. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER (for Short Body) |
![]() |
Using a screwdriver, detach the 4 claws and remove the cover.
| 17. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET (for Short Body) |
![]() |
Remove the bolt, 2 washers, collar and bracket.
| 18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Short Body) |
![]() |
Disconnect the rear No. 1 seat belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
![]() |
Remove the bolt and 2 screws.
Using a screwdriver, detach the 5 claws.
Using a clip remover, detach the 5 clips and remove the trim board.
Disconnect the power outlet socket connector.
Remove the belt hanger.
| 19. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for Long Body) |
![]() |
Disconnect the rear No.1 seat outer belt's floor anchor.
Remove the anchor cover.
Remove the bolt and disconnect the floor anchor.
![]() |
Remove the 2 screws and 2 bolts.
Using a screwdriver, detach the 5 claws.
Using a clip remover, detach the 4 clips and remove the trim board.
Disconnect the power outlet socket connector.
Remove the belt hanger.
| 20. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Short Body) |
![]() |
Using a clip remover, detach the 7 clips and remove the garnish.
| 21. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (for Long Body) |
| 22. REMOVE ROOF HEADLINING ASSEMBLY (for Short Body) |
Partially remove the roof headlining .
| 23. REMOVE ROOF HEADLINING ASSEMBLY (for Long Body) |
Partially remove the roof headlining .
| 24. REMOVE QUARTER WINDOW ASSEMBLY LH |
![]() |
Disconnect the connector.
From the interior, insert a piano wire between the vehicle body and the quarter window glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
![]() |
Cut through the adhesive by pulling the piano wire around the quarter window glass.
Using suction cups, remove the quarter window glass.
| 25. CLEAN QUARTER WINDOW ASSEMBLY |
![]() |
Clean the outer edges of the glass with non-residue solvent.
| 26. CLEAN VEHICLE BODY |
![]() |
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Clean the contact surface of the vehicle body with cleaner.